background image

LK Floor Heating | Assembly Instructions | LK Room Temperature Control ICS-RF8

29

EN.33.C.891008

Limitations

Min

Max

Notes

Number of thermostats per
ICS RF8

1

8

Number of actuators per ICS
RF8

1

12

Number of actuators per
channel ICS

1

3

It is possible to physically connect two per
contact.

Number of radio links per
system

1

1

With connected BUS

Number of ICS-RF 8 per
system

1

8

With connected BUS

Number of channels per
system

1

64

With connected BUS

Maximum number of
repeaters per system

0

4

Length of cable networks

-

75 m

With connected BUS

Cable length for Radio link
(cable type: modular cable
RJ9)

-

30 m

LK Aerial cable is 10 m

Comments

Totally trouble-free operation cannot always be guaranteed with the technology available today that allows free
use of EU authorised frequency bands (interference from other sources is possible). Therefore, each installation
should be tested individually.

Manufacturer set thermostat

Setting

Unit

Min

Max

Factory
settings

Holiday value

Days

1

90

1

Setback temperature °C

8

40

12

Economy
temperature

°C

8

40

18

Comfort temperature °C

8

40

20

Holiday temperature °C

8

40

12

Start time Comfort

Time, hours

00:00

24:00

06:00

Start Time Economy Time, hours

00:00

24:00

22:00

System clock

Number of days:
hours: minutes

0:00:00 7:23:59

1:00:00

Floor sensor min limit °C

7

40

10

Floor sensor max limit °C

7

40

27

Adaptive function

On/Off

-

-

Off

Background lighting
display

On/Off

-

-

Off

Key lock

On/Off

-

-

Off

Summary of Contents for ICS-RF8
































Reviews: