Lexmark Optra N 4040 Reference Handbook Download | Manualshive

Page: 100 / 259

background image

4039-1XX

5-7

40
39-

1

X

X

971 Network Card

Network card RAM failure. Replace the Network
Card.

972 Network Card

Network card ROS/FLASH failure. Replace the
Network Card.

973 Network Card

Network card EEPROM/NVRAM failure. Replace
the Network Card.

974 Network Card

Network card/Network interface error. Replace the
Network Card.

976 Network Card

Network card software error. Verify that the network
card is installed and grounded correctly. If this error
returns after a POR, there is a software or
microcode incompatibility problem. Do not replace
the card. Contact your next level of support.

977 Network Card

Network card is installed but is not communicating
with the system board. Refer to Network Card 977
Errors Service Check in your Service Manual.

978 Network Card

General network card hardware error. Replace the
Network Card.

979 Network Card

General network card software error. Verify that the
network card is installed and grounded correctly. If
this error returns after a POR, there is a software or
microcode incompatibility problem. Do not replace
the card. Contact your next level of support.

990 Duplex Option

Duplex error. Refer to Duplex Service Check in your
Service Manual.

991 Duplex System
Card Failure

Duplex system card failure. Replace the duplex
system card.

993 Duplex Comm.
Failure

Communications between the duplex unit and the
printer have failed. Refer to Duplex Service Check in
your Service Manual.

Error Message Table (Continued)

Error/Code

Action

«
...
98
99
100
101
102
...
»

Summary of Contents for Optra N 4040




































































































































































































































































Reviews:

No comments

Related manuals for Optra N 4040

Brand: Xerox Pages: 110

Brand: Olivetti Pages: 41

Brand: Minolta Pages: 193

IMAGERUNNER ADVANCE C5045

Brand: Canon Pages: 1131

Brand: Xerox Pages: 72

Brand: Oki Pages: 386

Brand: Lexmark Pages: 85

Brand: Lexmark Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands