Larson Davis 831 User Manual Download Page 455

Page: 455 / 548

A-18

Model 831 Specifications

Model 831 Manual

Power Supply

Battery Operating Lifetime

Power Consumption

Batteries

4-AA (LR6) NiMH, Alkaline or Energizer L91 e



Lithium

cells (supplied with 2500 mAH NiMH cells).

Warning: Use of battery cells with greater than 1.5 Volt
specified rating can damage the instrument and void the
warranty.

External Power

Powered through USB interface from computer or from
PSA029 AC to DC Power Adapter: 5 Volt



5% required.

Applying a voltage greater than specified can damage the
instrument and void the warranty.

External Power

Power through I/O connector: 10 to 15.5 Vdc. Use cable
CBL154 for 426A12, CBL140 for PSA027, or Model 831-
INT Interface Unit

Table A-15 Power Supply Specifications

Battery

Operating Life, Hours

4-AA (LR6) NiMH Cells

> 8

Table A-16 Battery Operating Lifetime

Model 831 Operating State

Watts

mA @ 12 Volts

mA @ 15 Volts

Running, Backlight Off, USB not connected

1.1

Running, Backlight Off, USB connected to PC

1.7

142

114

Running, Backlight Bright, USB connected to PC

2.9

238

190

Table A-17 Power Consumption

Summary of Contents for 831





































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 831

Reviews:

Related manuals for 831

Brands by name

Popular brands

Larson Davis 831, User Manual

Search results

Summary of Contents for 831

Reviews:

Related manuals for 831

Brands by name

Popular brands