Larson Davis 831 User Manual Download Page 512 | Manualshive

Page: 512 / 548

background image

Model 831 Manual

Sections 5, 6, 7 and 9 (except 9.3)

B-11

For a temperature change of 5 °C then 30 minutes are required.

For a static pressure change of 5 kPa then 15 seconds are required.

For a humidity change of 30% (non-condensing) then 30 minutes are required.

m) Field Strength > 10 V/m

The Larson Davis model 831 was not measured for field strengths greater than 10 V/m.

n) Radio Frequency Emission

The mode of operation of the 831 that produces the greatest radio frequency emission levels was with

the 831 set to run and with an EXC010 (10' microphone extension cable) used to connect the PRM831
to the 831.

o) AC Power and Radio Frequency Susceptibility

The mode of operation of the 831 that produced the greatest measurement susceptibility to A.C. power

frequency and radio frequency fields was with the 831 set to run, USB cable attached and with an
EXC010 (10' microphone extension cable) between the PRM831 and the 831.

«
...
510
511
512
513
514
...
»

Summary of Contents for 831





































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 831

Brand: Kane Pages: 16

Brand: Kane Pages: 60

Brand: Lumel Pages: 32

Brand: Gardner Bender Pages: 7

Brand: jenway Pages: 18

Brand: Mahr Pages: 384

WM14-96 - PROGRAMMING

Brand: CARLO GAVAZZI Pages: 6

Brand: MULTISPAN Pages: 4

Brand: Agilent Technologies Pages: 198

LaserRange-Master T4 Pro

Brand: LaserLiner Pages: 68

Brand: Hanna Instruments Pages: 2

Brand: ICP DAS USA Pages: 340

ENERGY MAX EM400

Brand: Molectron Pages: 40

Brand: Patlite Pages: 21

Brand: B&B Pages: 37

Brand: Badger Meter Pages: 20

Brand: Accumet Pages: 24

Brand: PASCO Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands