Larson Davis 831 User Manual Download Page 92

Page: 92 / 548

Model 831 Manual

Overall Tab

5-13

The 2nd numerical value displayed is L

Apeak

in this

example, is a user-selected value. The selection of this value
is described in “User-Selected SLM Parameter” below.

The time at the bottom of the page is the date and time the
measurement was started.

User-Selected SLM Parameter

To select which sound level parameter is to be utilized for
the 2nd numerical value displayed, press

to open the

menu shown in FIGURE 5-13

FIGURE 5-13 Menu for User-Selected

SLM Parameter

There are twenty-four possible
selections; scroll down to see more
than shown in FIGURE 5-13.

Highlight the desired parameter and press

to make the

selection.

Summary of Contents for 831





































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 831

Reviews:

Related manuals for 831

Brands by name

Popular brands

Larson Davis 831, User Manual

Search results

Summary of Contents for 831

Reviews:

Related manuals for 831

Brands by name

Popular brands