Larson Davis 831 User Manual Download Page 50

Page: 50 / 548

Model 831 Manual

Tab and Setting Displays

3-19

The Communication tabs include the following:

•

Status:

Display status of Analog and Wireless modems,

RS-232 and USB channels.

•

Modem:

Setup a dial-up modem

•

Wireless:

Setup a wireless modem

•

RS-232:

Setup an RS-232 interface

Calibrate

For a detailed description of the
calibration procedure, see Chapter 8
"Calibration" on page 8-1.

Calibrate is used to verify and adjust the calibration of the
Model 831 prior to a measurement.

Voice Recorder

For a detailed description of the
voice recording feature, see Chapter
10 "Voice Recording" on page 10-1.

A method to allow voice annotation of the data is described
in Chapter 10 "Voice Recording" on page 10-1.

About

For a detailed description of the
About tabs, see Chapter 22 "About"
on page 22-1.

The About tabs provide the user with information specific to
this instrument such as serial number, options, etc. These are
single section tabs.

The About tabs include the following:

•

About:

shows information such as serial number and

firmware revision

•

Standards:

lists the standards that the Model 831 meets

•

Options:

shows the options that are available in this

instrument

•

User:

user entered instrument identification

Summary of Contents for 831





































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 831

Reviews:

Related manuals for 831

Brands by name

Popular brands

Larson Davis 831, User Manual

Search results

Summary of Contents for 831

Reviews:

Related manuals for 831

Brands by name

Popular brands