manualshive.com logo in svg

Larson Davis 831, User Manual

Looking for a hassle-free setup? Our Met One 831 is just what you need! Download the Quick Setup Manual for this amazing product completely free from manualshive.com, where you can access a wide range of user manuals. Get a step-by-step guide to effortlessly set up your Met One 831 and enjoy its exceptional features.

Share
Download
background image

A-30

Position of Instrument and Operator 

Model 831 Manual

Position of Instrument and Operator

When making a measurement, it is recommended that the observer be positioned as far behind and to
the right of the instrument as possible to minimize interference of the sound field at the microphone
resulting from body reflections. When using the Model 831, the meter is held in one hand with the arm
extended away from the body. Better results can be obtained by using a tripod.

Effect of Windscreen

The corrections which should be subtracted from the measured data when using the Larson-Davis
Model WS001 3

½

 inch diameter windscreen with a 

½

 inch Larson-Davis microphone are as indicated

in the following table.

Continued on next page 

Directional Response Effect of 3½ Inch Wind Screen on 377B02 Microphone Attached to Model 831

Frequency

Angle from Reference direction (degrees)

(Hz)

0

15

30

45

60

75

90

105

120

135

150

165

180

251.19

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

266.07

0.00

0.00

0.03

-0.03

0.00

0.00

0.00

-0.03

0.03

0.00

-0.03

-0.03

0.00

281.84

0.00

0.10

0.07

-0.03

-0.07

0.00

0.03

0.00

0.07

0.00

-0.03

0.03

0.00

298.54

0.07

0.07

0.00

0.00

-0.03

0.00

0.03

-0.03

-0.03

0.03

-0.10

0.03

0.00

316.23

0.00

0.03

0.07

0.00

-0.07

-0.03

0.00

-0.03

0.03

-0.03

-0.10

0.07

0.00

334.97

0.00

0.00

0.03

0.00

-0.07

-0.03

0.07

-0.13

0.00

0.00

-0.07

0.07

0.00

354.81

0.03

0.07

0.10

-0.03

-0.07

0.00

0.00

-0.03

0.03

0.03

-0.03

0.03

0.00

375.84

0.03

0.07

0.03

0.00

-0.03

-0.03

0.00

-0.03

0.03

0.00

-0.10

0.00

0.00

398.11

0.00

0.00

0.10

-0.03

-0.03

0.00

0.00

-0.03

0.07

-0.03

-0.07

0.07

0.07

421.70

0.00

0.00

0.07

0.03

-0.07

-0.03

0.00

-0.03

0.03

0.00

-0.07

0.00

0.00

446.68

0.00

0.03

0.03

-0.03

0.00

-0.03

0.10

0.03

0.03

0.00

0.00

0.00

0.00

473.15

0.03

0.03

0.03

0.00

0.03

-0.03

0.07

0.00

0.03

0.00

-0.07

0.03

0.00

501.19

0.10

0.10

0.13

0.07

-0.03

0.07

0.00

0.00

0.13

0.10

-0.07

0.03

0.00

530.88

0.03

0.10

0.13

0.07

-0.07

0.07

0.03

0.03

0.07

0.00

-0.03

0.03

0.00

562.34

0.10

0.10

0.13

0.07

0.03

0.07

0.00

-0.03

0.13

0.10

-0.03

0.00

0.07

595.66

0.07

0.10

0.13

0.07

-0.03

0.03

0.00

0.00

0.10

0.07

-0.03

0.07

0.00

630.96

0.03

0.00

0.07

-0.03

0.00

0.07

0.10

0.07

0.13

0.10

0.03

0.10

0.10

668.34

0.10

0.10

0.13

0.07

0.03

0.00

0.03

0.03

0.07

0.00

0.03

0.10

0.00

707.95

0.10

0.10

0.13

0.07

0.03

0.07

0.10

0.07

0.03

0.10

0.03

0.10

0.00

749.89

0.10

0.10

0.13

0.07

0.00

-0.03

0.10

0.07

0.13

0.10

0.03

0.10

0.10

794.33

0.10

0.10

0.13

0.07

0.03

0.13

0.10

0.07

0.13

0.10

0.03

0.10

0.10

841.40

0.03

0.07

0.10

0.07

0.03

0.07

0.10

0.10

0.03

0.10

0.03

0.10

0.10

891.25

0.10

0.07

0.10

0.00

0.03

0.07

0.03

0.07

0.13

0.07

0.03

0.10

0.10

944.06

0.13

0.17

0.20

0.07

0.07

0.07

0.13

0.17

0.20

0.17

0.03

0.17

0.13

1000.00

0.20

0.10

0.13

0.07

0.03

0.17

0.10

0.17

0.23

0.10

0.03

0.10

0.10

1059.25

0.10

0.10

0.23

0.17

0.13

0.07

0.10

0.07

0.13

0.10

0.03

0.10

0.10

1122.02

0.20

0.23

0.23

0.13

0.13

0.17

0.10

0.17

0.23

0.20

0.13

0.13

0.10

1188.50

0.20

0.10

0.23

0.07

0.13

0.17

0.10

0.17

0.13

0.20

0.13

0.17

0.10

1258.93

0.13

0.17

0.23

0.17

0.13

0.17

0.23

0.13

0.23

0.17

0.13

0.10

0.20

1333.52

0.20

0.20

0.33

0.27

0.13

0.17

0.20

0.23

0.23

0.20

0.13

0.20

0.10

1412.54

0.20

0.20

0.23

0.17

0.23

0.17

0.20

0.27

0.23

0.20

0.13

0.17

0.20

1496.24

0.23

0.20

0.23

0.17

0.23

0.17

0.20

0.27

0.23

0.27

0.13

0.10

0.20

1584.89

0.33

0.30

0.37

0.30

0.27

0.27

0.33

0.27

0.30

0.27

0.20

0.27

0.30

1678.80

0.30

0.30

0.40

0.37

0.33

0.27

0.30

0.27

0.33

0.20

0.17

0.20

0.27

1778.28

0.40

0.40

0.43

0.37

0.33

0.33

0.40

0.37

0.33

0.40

0.13

0.30

0.30

1883.65

0.40

0.40

0.43

0.37

0.33

0.37

0.40

0.37

0.33

0.30

0.23

0.30

0.30

1995.26

0.40

0.50

0.43

0.47

0.43

0.47

0.40

0.37

0.37

0.40

0.23

0.33

0.30

2113.49

0.50

0.50

0.53

0.47

0.43

0.47

0.40

0.47

0.43

0.37

0.33

0.33

0.40

2238.72

0.50

0.50

0.53

0.47

0.43

0.47

0.50

0.47

0.47

0.40

0.30

0.40

0.40

2371.37

0.50

0.50

0.53

0.47

0.43

0.47

0.50

0.47

0.53

0.50

0.33

0.50

0.40

2511.89

0.50

0.57

0.53

0.57

0.50

0.57

0.53

0.53

0.53

0.50

0.37

0.47

0.47

2660.73

0.53

0.53

0.57

0.57

0.50

0.50

0.60

0.50

0.53

0.50

0.43

0.50

0.43

2818 38

0 57

0 53

0 57

0 60

0 50

0 50

0 53

0 53

0 57

0 57

0 43

0 57

0 50

Summary of Contents for 831





































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 831

Danfoss EKC 201 Manual preview
EKC 201
Brand: Danfoss Pages: 6
Datalogic Smart-VS Quick Reference Manual preview
Smart-VS
Brand: Datalogic Pages: 6
Datakom DKM-411 Quick Start Manual preview
DKM-411
Brand: Datakom Pages: 4
Datakom DKM-407 User Manual preview
DKM-407
Brand: Datakom Pages: 38
Omega DP25B-E User Manual preview
DP25B-E
Brand: Omega Pages: 74
Omega CL1000 Series User Manual preview
CL1000 Series
Brand: Omega Pages: 24
X-Rite DensiEye 100 Reference Manual preview
DensiEye 100
Brand: X-Rite Pages: 50
Yamaha Portable Grand DGX-670 Reference Manual preview
Portable Grand DGX-670
Brand: Yamaha Pages: 93
Yamaha Portatone PSR-410 Manual De Instrucciones preview
Portatone PSR-410
Brand: Yamaha Pages: 65
UFM CoolPoint CP12-V8 Installation And Operation Manual preview
CoolPoint CP12-V8
Brand: UFM Pages: 14
TDI Nitro-Save NS16 Operating Instructions preview
Nitro-Save NS16
Brand: TDI Pages: 4
Omega HHLM-2 User Manual preview
HHLM-2
Brand: Omega Pages: 13
PITSID NIP CON SMART Operation Manual preview
NIP CON SMART
Brand: PITSID Pages: 22
Swan Analytical Instruments AMI Silica Operator'S Manual preview
AMI Silica
Brand: Swan Analytical Instruments Pages: 102
SKF Microlog GX Series User Manual preview
Microlog GX Series
Brand: SKF Pages: 342
Tohnichi 5TM Operating Instruction preview
5TM
Brand: Tohnichi Pages: 12
Kawai Concert Performer Series Digital Piano CP110 Owner'S Manual preview
Concert Performer Series Digital Piano CP110
Brand: Kawai Pages: 149
WAGNER Datamaster Quick Start Manual preview
Datamaster
Brand: WAGNER Pages: 4

Brands by name

Popular brands

Load more brands