3-5
MAIN FRAME ASSEMBLY - 18’ MODEL
Note:
See
Figure
3-6
for
frame
assembly
drawing.
Note: For center frame location, see Figure
3-23.
3-5.1
Place the main frame on stands 30“ high.
Assemble the left and right auxiliary frames
to the main frame as shown with u-bolts,
lockwashers, and nuts.
3-5.2
Place the transport axle under the frame-
work. Position transport axle with cylinder
mount up and cylinder pin to the front. Install
transport axle bearings between axle and
frames. Secure with axle straps, placing 3/4”
x 6” bolt up from bottom.
3-5.3
Mount the tires and rims to the axle hubs
at this time.
3-5.4
Before the front roller assembly is bolted to
the main frame structure, the two transport
level mounting spring must be pre-positioned
on the 4” x 4” cross tube of the frame work.
(Mounting springs and hardware are pack-
aged in the transport level bundle).
3-5.5
Raise the front roller assembly up under
the frame plates or lower frame to the gang
assembly. Center the roller gang on the
framework and install with 7/8” u-bolts, lock-
washers, and nuts.
IMPORTANT
WHEN INSTALLING ROLLER GANGS ON THE
MULCHER FRAME, BE SURE THE GREASE FIT-
TINGS POINT TO THE REAR OF THE MACHINE.
THIS WILL INSURE THAT THE BEARING LOCK
COLLARS WILL FUNCTION PROPERLY AND
NOT LOOSEN DURING FIELD OPERATION.
3-5.6
Raise the rear roller assembly up under
frame plates or lower the frame to the roller
assembly. Center roller assembly on the
framework.
3-5.7
Attach the pull tongue assembly to main
frame using hitch pin and 3/8” x 2-1/2” spring
pin. Mount tongue jack to side of tongue. In-
stall the hose support bracket to tongue with
3/4” x 1” bolt and lockwasher. Loosely as-
semble hose holder to support bracket.
Tighten after hydraulic hoses have been in-
stalled.
3-5.8
Assemble the automatic transport lock to
ear on main frame tube. Place two 1” flat
washers on each side of ear between the
transport lock plate, using pivot pin and klip
pins to assemble. Hook the actuator spring
to automatic transport lock and spring anchor
on main frame tube. Slide the actuator rod
through guide plate on frame tube. Place
3/8” flat washer and 1/8” x 1” cotter pin on
each side of transport lock plate to mount.
Place bend end of actuator rod in two-hole
plate on frame.
3-5.9
Install reflectors to frame as indicated.
3-9
Summary of Contents for 3210 Series
