4.2 CLEANING AND SANITIZING SOLUTIONS
CLEANING SOLUTION
: Mix a mild, non-abrasive detergent with clean, potable water at a
temperature of 90 to 110°F (32 to 43°C). The mixture ratio is one ounce of cleaner to two gallons
of water. prepare a minimum of five gallons of cleaning solution. Do not use abrasive cleaners or
solvents because they can cause permanent damage to the unit. rinsing must be thorough, using
clean, potable water at a temperature of 90 to 110°F (32 to 43°C). Extended lengths of product lines
may require that an additional volume of cleaning solution be prepared.
SANITIZING SOLUTION:
Prepare sanitizing solutions in accordance with the manufacturer’s
written recommendations and safety guidelines. The solution must provide 50 to 100 parts per
million (ppM) chlorine. A minimum of five gallons of sanitizing solution should be prepared. Any
sanitizing solution may be used as long as it is prepared in accordance with the manufacturer’s
written recommendations and safety guidelines, and provides 50 to 100 parts per million (ppM)
chlorine. Extended lengths of product lines may require that an additional volume of sanitizing
solution be prepared.
Other Supplies Needed:
• Sanitary gloves
• Clean cloth towels
• Extra nozzle
• Bucket
• Small brush (pN 22-0017), included with installation kit
USE SANITARY GLOVES.
OBSERVE APPLICABLE SAFETY PRECAUTIONS.
x
DO NOT USE A WATER JET TO CLEAN OR SANITIZE THE UNIT
x
DO NOT DISCONNECT WATER LINES WHEN CLEANING AND SANITIZING SYRUP LINES, TO
AVOID CONTAMINATION.
x
DO NOT USE STRONG BLEACHES OR DETERGENTS; THESE CAN DISCOLOR AND
CORRODE VARIOUS MATERIALS.
x
DO NOT USE METAL SCRAPERS, SHARP OBJECTS, STEEL WOOL, SCOURING PADS,
ABRASIVES, OR SOLVENTS ON THE DISPENSER.
x
DO NOT USE HOT WATER ABOVE 140º F (60º C). THIS CAN DAMAGE THE DISPENSER.
x
DO NOT SPILL SANITIZING SOLUTION ON ANY CIRCUIT BOARDS. INSURE ALL SANITIZING
SOLUTION IS REMOVED FROM THE SYSTEM.
!
WARNING
IF A POWDER SANITIZER IS USED, DISSOLVE IT THOROUGHLY WITH HOT WATER PRIOR TO
ADDING TO THE SYRUP SYSTEM. ENSURE SANITIZING SOLUTION IS REMOVED FROM THE DISPENSER AS
INSTRUCTED. AVOID GETTING SANITIZING SOLUTION ON CIRCUIT BOARDS. DO NOT USE STRONG BLEACHES
OR DETERGENTS; THESE CAN DISCOLORAND CORRODE VARIOUS MATERIALS. DO NOT USE METAL
SCRAPERS, SHARP OBJECTS, STEEL WOOL, SCOURING PADS, ABRASIVES, OR SOLVENTS ON THE
DISPENSER. DO NOT USE HOT WATER ABOVE 140° F (60° C). THIS CAN DAMAGE THE DISPENSER.
ADVERTENCIA
SI SE USA UN HIGIENIZADOR EN POLVO, DISUÉLVALO BIEN EN AGUA ANTES DE AGREGARLO
AL SISTEMA DE CONCENTRADO. EL USO DE AGUA CALIENTE CONTRIBUYE A DISOLVER LOS HIGIENIZADORES
EN POLVO. ASEGÚRESE DE HABER ELIMINADO LA SOLUCIÓN DE ESTERILIZACIÓN DEL
DISPENSADOR DE ACUERDO CON LAS INSTRUCCIONES. LOS RESIDUOS DE LA SOLUCIÓN DE
ESTERILIZACIÓN REPRESENTAN UN PELIGRO PARA LA SALUD. EVITE QUE LA SOLUCIÓN DE ESTERILIZACIÓN
LLEGUE A LAS PLACAS DE CIRCUITOS. NO USE LAVANDINAS NI DETERGENTES QUE PODRÍAN QUITAR EL
COLOR Y CORROER DISTINTOS MATERIALES. NO USE RASPADORES METÁLICOS, OBJETOS FILOSOS, LANA
DE ACERO, ESTROPAJOS, ABRASIVOS NI SOLVENTES EN EL DISPENSADOR. NO USE AGUA CALIENTE A MÁS
DE 140 ºF (60 ºC). PODRÍA DAÑAR EL DISPENSADOR.
AVERTISSEMENT
AVANT L’INJECTION DANS LE SYSTÈME, IL FAUDRA QUE LA POUDRE SEPTIQUE SOIT
DISSOLUE ENTIÈREMENT DANS CHAUDE. L’EAU CHAUDE PERMETTRA UN MEILLEUR PROCÈS DE
DISSOLUTION. SUIVANT LES INSTRUCTIONS JOINTES, IL EST IMPÉRATIF QUE LA SOLUTION SEPTIQUE SOIT
ENTIÈREMENT ENLEVÉE. EVITEZ DE METTRE LA SOLUTION EN CONTACT AVEC LES CIRCUITS. N’UTILISEZ PAS
DE JAVELLISANTS OU DEDÉTERGENTS FORTS; CEUX-CI PEUVENT DÉCOLORER ET CORRODER DIVERS
MATÉRIAUX. N’UTILISEZ PAS DE RACLEURS EN MÉTAL, D’OBJETS POINTUS, DE LAINE D’ACIER, DE TAMPONS À
RÉCURER, D’ABRASIFS OU DE SOLVANTS SUR LE DISTRIBUTEUR. N’UTILISEZ PAS DE L’EAU CHAUDE DE PLUS
DE 140 DEGRÉS F (60 DEGRÉS C). CECI PEUT ENDOMMAGER LE DISTRIBUTEUR.
19
