background image

 

1.4   ALTERNATE METHOD: SIGHT TUBE (4-VALVE ONLY)

 

 

A.   Connect a short length of the appropriate-sized clear tubing over the hose barbed end of the  

 

drain fitting (see Illustration 44 at end of manual).

 

 

B.   Rotate the fitting counterclockwise to open the drain.

 

 

C.   Open the doors, add water and hold the clear tube until the water level rises to the center of the  

 

hole on the pump platforms sheet metal.

 

 

D.   Close drain by gently rotating the fitting clockwise. The drain fitting threads in and out and seals  

 

with o-rings.

 

 

E.   Remove length of tubing.

 

1.5   CONNECTING THE WATER SUPPLY 

- See WATER NOTICE on page 9

 

 

Install the dispenser with adequate backflow protection to comply with applicable federal, state and 

local codes. This is an NSF requirement.

 

 

A.   Install the dispenser with the water and electric supply entering through an access plate in the  

 

back of the wrapper, or through a hole in the countertop, directly into the dispenser.

 

 

B.   Flush the water supply line thoroughly.

 

 

C.   Remove drip tray by pulling up slightly, while lifting away from the dispenser.

 

 

D.   Remove splash plate by pulling the bottom up slightly, then out from the dispenser.

 

 

E.   The installation kit contains both a straight connector (for through the countertop) and an elbow  

 

connector (for through the back of the dispenser). Use the appropriate connector for the 

 

 

 

preferred set-up and securely attach to the included tubing with clamp.

 

 

F.   Lubricate the o-rings on the fitting and insert into the 1/4 turn shutoff valve and secure with 

 

 

 

sliding clip. (On installations going through the back of the wrapper, remove the cover plate on  

 

the back of the dispenser and thread the tubing through the lower section of the machine and  

 

out the back.)

 

1.6  ELECTRICAL REQUIREMENTS

F

WARNING

 WHEN USING ELECTRIC APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,

INCLUDING THE FOLLOWING:
A. READ ALL THE INSTRUCTIONS BEFORE USING THE APPLIANCE.

B. DO NOT USE OUTDOORS.

C. DO NOT UNPLUG BY PULLING ON THE CORD.

D. FOR A GROUNDED APPLIANCE, CONNECT TO PROPERLY GROUNDED OUTLET ONLY. SEE GROUNDING 

INSTRUCTIONS.

E. UNPLUG FROM OUTLET BEFORE SERVICING OR CLEANING.

ADVERTENCIA 

 CUANDO SE UTILIZAN APARATOS ELÉCTRICOS, LAS PRECAUCIONES BÁSICAS SIEMPRE SE 

DEBEN SEGUIR, INCLUYENDO LAS SIGUIENTES:
A. LEA TODAS LAS INSTRUCCIONES ANTES DE USAR EL APARATO.

B. NO USAR EN EXTERIORES. 

C. NO DESENCHUFE TIRANDO DEL CORDÓN. 

D. PARA UN APARATO CON CONEXIÓN A TIERRA, CONEXIÓN A TIERRA ADECUADA TOMA SOLAMENTE. VEA 

CONEXIÓN A TIERRA INSTRUCCIONES. 

E. DESCONECTE DEL TOMACORRIENTE ANTES DE REPARAR O LIMPIAR.

AVERTISSEMENT

 DES PRÉCAUTIONS DE BASE DOIVENT TOUJOURS ÊTRE SUIVIES LORSQUE DES 

APPAREILS MÉNAGERS ÉLECTRIQUES SONT UTILISÉS, NOTAMMENT :
A. LIRE TOUTES LES INSTRUCTIONS AVANT D’UTILISER L’APPAREIL.

B. NE PAS UTILISER À L’EXTÉRIEUR.

C. NE JAMAIS TIRER SUR LE CORDON POUR DÉBRANCHER L’APPAREIL.

D. BRANCHER TOUT APPAREIL DEVANT ÊTRE MIS À LA TERRE UNIQUEMENT SUR UNE PRISE AVEC MISE À LA 

TERRE. VOIR LES INSTRUCTIONS DE MISE À LA TERRE.

E. DÉBRANCHER L’APPAREIL DE LA PRISE AVANT DE LE RÉPARER OU DE LE NETTOYER.

12

Summary of Contents for 28-0586/07























































Reviews: