Kyocera TASKalfa 250ci Operation Manual Download Page 93

Page: 93 / 488

Basic Operation

OPERATION GUIDE

3-21

Offset

Without Document Finisher

If the optional document finisher is not installed, when
you use offsetting, printed copies are produced after
rotating each set (or page) by 90º.

NOTE:

You need to load the same sized paper with

different orientation in the paper source other than the
selected paper source. The paper sizes supported in

Offset

are A4, B5, Letter and 16K.

With Document Finisher

When you use offsetting, printed copies are segregated
after each set of copies (or after each page).

NOTE:

The optional document finisher or 3,000 sheet

document finisher is required.

The procedure for using collate/offset copying is
explained below.

Press the

Copy

key.

Place the originals on the platen.

Press [Org./Paper/Finishing] and then [Collate/
Offset].

To use collate copying, press [On] of

Collate

To use offset copying, press [Each Set] of

Offset

Press [OK].

Original

Copy (each set)

Original

Copy (each set)

Off

Each Set

Off

Collate/Offset

Offset

Ready to copy.

Copies

Status

10/10/2008 10:10

Cancel

Add Shortcut

Collate

Preview

Original
Zoom
Paper

100%
---

:
:
:

---

Place original.

Summary of Contents for TASKalfa 250ci









































































































































































































































































































































































































































































































Search results

Summary of Contents for TASKalfa 250ci

Reviews:

Brands by name

Popular brands

Kyocera TASKalfa 250ci, Operation Manual

Search results

Summary of Contents for TASKalfa 250ci

Reviews:

Brands by name

Popular brands