Kronoterm HM-130 S1 Instructions For Installation, Use And Maintenance Manual Download Page 48 | Manualshive

Page: 48 / 60

background image

48

3.6.12

CONNECTING THE SIGNAL FOR PV SIGNAL

NOTE

Connect the PV signal in case you have a combination of PV collectors and a
heat pump. Set the controller for the desired function when the signal is present.

NOTE

The PV signal and remote switch between heating / cooling cannot be
connected at the same time.

Connect the PV signal to serial clamp X4,
connect it to D8 and GND.

The signal must be short-circuited and
potential-free.

3.6.13

CONNECTING THE SIGNAL FOR REMOTE OFF

NOTE

Connect the signal for remote off in case the heating system is controlled by an
external controller.

Connect the signal for remote switch to serial
clamp X4, connect it to D5 and GND.

The signal must be short-circuited and
potential-free.

3.7 Commissioning of the device

After professional installation, the authorised contractor for commissioning has to perform

the commissioning of the device.

CAUTION

The commission can only be performed by a person authorised by the
manufacturer! If the commission is performed by an unauthorised person, the
warranty is not recognised.

CAUTION

Before commissioning, it is necessary to perform all the required tasks and
inspections from the tasks for commission.

«
...
46
47
48
49
50
...
»

Summary of Contents for HM-130 S1





























































Reviews:

No comments

Related manuals for HM-130 S1

Brand: JBL Pages: 12

Goulds CentriPro M05411

Brand: Xylem Pages: 68

Signature XP19-024

Brand: Lennox Pages: 32

Brand: NuTone Pages: 8

Brand: HOFFEN Pages: 40

Brand: mundoclima Pages: 8

Brand: ProMinent Pages: 77

KLIMATRONIC HEAT SUPREME

Brand: Suntec Wellness Pages: 124

Brand: Annovi Reverberi Pages: 4

Aquantia KHPMS-BI Series

Brand: Kaysun Pages: 40

Brand: wallas Pages: 38

Brand: Unitary products group Pages: 16

Inverter Design

Brand: Thermia Pages: 16

Brand: vacuubrand Pages: 72

Brand: Ingersoll-Rand Pages: 1

Brand: Dirty Hand Tools Pages: 20

Brand: U-Line Pages: 9

Brand: Carrier Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands