manualshive.com logo in svg

Kronoterm HM-130 S1, Instructions For Installation, Use And Maintenance Manual

The Kronoterm HM-130 S1 is a cutting-edge heating controller that ensures optimal temperature and comfort in your home. To conveniently set up and operate this innovative device, make sure to download the Instructions For Installation, Use And Maintenance Manual from our website. It's free and just a click away!

Share
Download
background image

29 

 
The minimal volume of the buffer tank V

min

 = 11 kW x 15 L/kW = 165 L 

 

 

Picture 13: Scheme of a system with several heating cycles, buffer tank and DHW buffer tank  

3.5.3.3 Bivalent system 

A  bivalent  system uses an  additional  heat  generator  in addition  to  the heat pump  to heat 

the building. 

Set up the bivalent system in accordance with the schemes below. 

Summary of Contents for HM-130 S1





























































Reviews:

No comments

Related manuals for HM-130 S1

Waves TH-104982.1 Manual preview
TH-104982.1
Brand: Waves Pages: 24
AUTOTERM PLANAR 2D-12 Installation Manual preview
PLANAR 2D-12
Brand: AUTOTERM Pages: 18
Xylem LOWARA e-SVE Additional Installation, Operation And Maintenance Instructions preview
LOWARA e-SVE
Brand: Xylem Pages: 56
Grundfos JPA 12-41 Installation And Operating Instructions Manual preview
JPA 12-41
Brand: Grundfos Pages: 16
Hypro 1542A-SP Series Installation, Operation, Repair And Parts Manual preview
1542A-SP Series
Brand: Hypro Pages: 8
Noctua NF-B9 PWM User Manual preview
NF-B9 PWM
Brand: Noctua Pages: 2
JABSCO CENTRI PUPPY 18510-000 Series Manual preview
CENTRI PUPPY 18510-000 Series
Brand: JABSCO Pages: 4
Dru ART 10-02 Instructions For Installation And Operation Manual preview
ART 10-02
Brand: Dru Pages: 56
Pacific hydrostar PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float... Manual preview
PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float...
Brand: Pacific hydrostar Pages: 9
VARISCO ST-R Series Instructions For Use And Maintenance Manual preview
ST-R Series
Brand: VARISCO Pages: 16
CLIMASTAR SILICIUM SLIM WIRELESS User Manual preview
SILICIUM SLIM WIRELESS
Brand: CLIMASTAR Pages: 20
Silverline 345678 User Manual preview
345678
Brand: Silverline Pages: 28
coval LEMAX90X B3 Series Operating Instruction preview
LEMAX90X B3 Series
Brand: coval Pages: 13
OMAC HD 8000 Manual preview
HD 8000
Brand: OMAC Pages: 42
Waves HO-101413 Manual preview
HO-101413
Brand: Waves Pages: 17
Somogyi home FKOS 11 Instruction Manual preview
home FKOS 11
Brand: Somogyi Pages: 12
DeWalt 2531DL-0078 Instruction Manual preview
2531DL-0078
Brand: DeWalt Pages: 108
Larzep WAP0025 Instruction Manual preview
WAP0025
Brand: Larzep Pages: 4

Brands by name

Popular brands

Load more brands