manualshive.com logo in svg

Kronoterm HM-130 S1, Instructions For Installation, Use And Maintenance Manual

The Kronoterm HM-130 S1 is a cutting-edge heating controller that ensures optimal temperature and comfort in your home. To conveniently set up and operate this innovative device, make sure to download the Instructions For Installation, Use And Maintenance Manual from our website. It's free and just a click away!

Share
Download
background image

30 

3.5.3.3.1 Bivalent system with oil or pellet furnace 

 

NOTE 

An expansion regulation TT 3003 - MD2 must be installed for regulation of the third 
cycle (5.3), fourth cycle (5.4) and circulation (10). 

 

 

Picture 14: Scheme of a bivalent system with oil or pellet furnace.  

 

3.5.3.3.2 Bivalent system with gas furnace 

 

NOTE 

An expansion regulation TT 3003 - MD2 must be installed for regulation of the third 
cycle (5.3), fourth cycle (5.4) and circulation (10). 

 

 

Picture 15: Scheme of a bivalent system with gas furnace.  

Summary of Contents for HM-130 S1





























































Reviews:

No comments

Related manuals for HM-130 S1

PAPILLON MANTA Instruction Manual preview
MANTA
Brand: PAPILLON Pages: 22
Wilo VeroLine-IPS 20 Installation And Operating Instructions Manual preview
VeroLine-IPS 20
Brand: Wilo Pages: 42
Gardena 1489 Operating Instructions Manual preview
1489
Brand: Gardena Pages: 10
Wacker Neuson PT 6L Operator'S Manual preview
PT 6L
Brand: Wacker Neuson Pages: 72
Aquatec AQUAPRO AP1000FP Instruction Manual preview
AQUAPRO AP1000FP
Brand: Aquatec Pages: 2
Jandy SHPF Installation And Operation Manual preview
SHPF
Brand: Jandy Pages: 24
SPERONI AGC 1100/25 Operating Instructions Manual preview
AGC 1100/25
Brand: SPERONI Pages: 68
EBARA EPD Instruction And Operation Manual preview
EPD
Brand: EBARA Pages: 28
RADSON MENAI D E - MOUNTING Instruction preview
MENAI D E - MOUNTING
Brand: RADSON Pages: 4
ARESA AR-2906 Instruction Manual preview
AR-2906
Brand: ARESA Pages: 13
Garland GEISER 281 G Instruction Manual preview
GEISER 281 G
Brand: Garland Pages: 100
STIEBEL ELTRON CK 20 S euro Operating And Installation Instructions preview
CK 20 S euro
Brand: STIEBEL ELTRON Pages: 20
Cosmo C2PGRAC625NN Instructions For Use Manual preview
C2PGRAC625NN
Brand: Cosmo Pages: 48
Costa Atlantis LF Owner'S Manual preview
Atlantis LF
Brand: Costa Pages: 12
Elite 11000EPH90 Installation And User Manual preview
11000EPH90
Brand: Elite Pages: 9
Sears 583.400040 Owner'S Manual preview
583.400040
Brand: Sears Pages: 9
GORMAN-RUPP PUMPS 2D-X.75 1P Installation, Operation And Maintenance Manual preview
2D-X.75 1P
Brand: GORMAN-RUPP PUMPS Pages: 25
Intex 620PC Owner'S Manual preview
620PC
Brand: Intex Pages: 5

Brands by name

Popular brands

Load more brands