manualshive.com logo in svg

Kronoterm HM-130 S1, Instructions For Installation, Use And Maintenance Manual

The Kronoterm HM-130 S1 is a cutting-edge heating controller that ensures optimal temperature and comfort in your home. To conveniently set up and operate this innovative device, make sure to download the Instructions For Installation, Use And Maintenance Manual from our website. It's free and just a click away!

Share
Download
background image

23 

 

 

Inside diameter 

– Φ22,2 - ±0,2 

 

4.  Align  the  expanded  connecting  pipes  with  the  connections.  Wrap  a  wet  towel 

around  the  connections  on  the  internal  unit  for  cooling.  Solder  the  pipes  with 

soldering which contains at least 5% Ag. 

 

 

 

 

5.  Check the quality of the joints. 

3.4.3 MAKE A LEAK TEST, DRAIN AND FILL THE COOLING 

CONNECTION. 

 

NOTE 

To perform the leak test, drain the system and fill the system, see 

Instructions for 

Installation, Use and Maintenance

 of the outdoor unit. 

Summary of Contents for HM-130 S1





























































Reviews:

No comments

Related manuals for HM-130 S1

DAB NOVA Instruction For Installation And Maintenance preview
NOVA
Brand: DAB Pages: 13
Watson Marlow Pumps 530 Series Manual preview
530 Series
Brand: Watson Marlow Pumps Pages: 95
Watson Marlow Pumps 530 Series Operating Manual preview
530 Series
Brand: Watson Marlow Pumps Pages: 87
Watson Marlow Pumps 530 Series Installation, Operating And Maintenance Manual preview
530 Series
Brand: Watson Marlow Pumps Pages: 127
ubbink Air 200 Manual preview
Air 200
Brand: ubbink Pages: 31
AquaPRO TSC130 PRO Operating And Parts Manual preview
TSC130 PRO
Brand: AquaPRO Pages: 4
Aspen Pumps mini aqua pump Installation & Maintenance Manual preview
mini aqua pump
Brand: Aspen Pumps Pages: 13
Modine Manufacturing GEO16-501.4 Installation And Service Manual preview
GEO16-501.4
Brand: Modine Manufacturing Pages: 28
usha FH 3114 S Instruction Manual preview
FH 3114 S
Brand: usha Pages: 8
Vagner Pool Rapid RH25L Installation And User Manual preview
Rapid RH25L
Brand: Vagner Pool Pages: 35
ARDES AR4P17 Instructions For Use Manual preview
AR4P17
Brand: ARDES Pages: 28
Remco SMOOTHFLO Series Operational preview
SMOOTHFLO Series
Brand: Remco Pages: 2
Conel FLOW TPF Installation And Operation Instructions Manual preview
FLOW TPF
Brand: Conel Pages: 104
Gabarron Elnur ECOMBI HHR Series Installation Instructions Manual preview
Elnur ECOMBI HHR Series
Brand: Gabarron Pages: 17
Honda WSP33 Operator'S Manual preview
WSP33
Brand: Honda Pages: 25
Heatstore Frost Guard HSMP05 Instructions preview
Frost Guard HSMP05
Brand: Heatstore Pages: 2
Vastar GX300A User Manual preview
GX300A
Brand: Vastar Pages: 4
Newmac NMLP120 Manual preview
NMLP120
Brand: Newmac Pages: 20

Brands by name

Popular brands

Load more brands