manualshive.com logo in svg

Kronoterm HM-130 S1, Instructions For Installation, Use And Maintenance Manual

The Kronoterm HM-130 S1 is a cutting-edge heating controller that ensures optimal temperature and comfort in your home. To conveniently set up and operate this innovative device, make sure to download the Instructions For Installation, Use And Maintenance Manual from our website. It's free and just a click away!

Share
Download
background image

18 

 

Picture 8: Coolant connection between the exterior and interior device.  

1 

Hydro module 

A 

Gas pipe 

2 

Outdoor unit 

B 

Liquid pipe 

 

You will need the following tools: 

  Screwdriver. 

  Coolant service manometer. 

  Tool for cutting pipes. 

  Tool for deburring pipes. 

  Fork wrench and fork torque wrench - for HM-140 S1 and HM-130 S1. 

  Tool for pipe edging - for HM-140 S1 and HM-130 S1. 

  POE oil is suitable for cooling systems - for HM-140 S1 and HM-130 S1. 

  Pipe expander - for HM-180 S1. 

  Acetylene burner, oxygen - for HM-180 S1. 

  Wet towel. 

Summary of Contents for HM-130 S1





























































Reviews:

No comments

Related manuals for HM-130 S1

Jaga Helios Installation And Operation Manual preview
Helios
Brand: Jaga Pages: 96
Radialight TOUCH Installation And Operating Manual preview
TOUCH
Brand: Radialight Pages: 36
wallas 270 Installation, Operation And Service Instructions preview
270
Brand: wallas Pages: 6
Jaga Knockonwood DBE KNUF Assembling Instructions preview
Knockonwood DBE KNUF
Brand: Jaga Pages: 4
Jaga Micro Canal Mounting Instructions preview
Micro Canal
Brand: Jaga Pages: 8
Jaga BRIZA 041 Installation Instructions Manual preview
BRIZA 041
Brand: Jaga Pages: 12
Pace PH 100 Operation Manual preview
PH 100
Brand: Pace Pages: 13
YAMADA NDP-5 series Maintenance Manual preview
NDP-5 series
Brand: YAMADA Pages: 14
Waterous S200-P Series Operation And Maintenance Instructions preview
S200-P Series
Brand: Waterous Pages: 10
Baker Hughes Druck PV 210 Instruction Manual preview
Druck PV 210
Brand: Baker Hughes Pages: 78
Oase ProMax Garden 3500 Operating Instructions Manual preview
ProMax Garden 3500
Brand: Oase Pages: 201
Simer 4850C Owner'S Manual preview
4850C
Brand: Simer Pages: 24
Flux F 550 GS Series Original Main Operating Instructions preview
F 550 GS Series
Brand: Flux Pages: 116
Continental Hydraulics H Design Series Service Manual preview
H Design Series
Brand: Continental Hydraulics Pages: 8
Biral AX 12 Installation And Operating Instructions Manual preview
AX 12
Brand: Biral Pages: 104
Goodman GSZ14 Manual preview
GSZ14
Brand: Goodman Pages: 56
Pfeiffer Vacuum OKTA 2000 ATEX Operating Instructions Manual preview
OKTA 2000 ATEX
Brand: Pfeiffer Vacuum Pages: 64
Ingersoll-Rand ARO PF20 B Series Operator'S Manual preview
ARO PF20 B Series
Brand: Ingersoll-Rand Pages: 8

Brands by name

Popular brands

Load more brands