manualshive.com logo in svg

Kronoterm HM-130 S1, Instructions For Installation, Use And Maintenance Manual

The Kronoterm HM-130 S1 is a cutting-edge heating controller that ensures optimal temperature and comfort in your home. To conveniently set up and operate this innovative device, make sure to download the Instructions For Installation, Use And Maintenance Manual from our website. It's free and just a click away!

Share
Download
background image

46 

 

Connect  the  thermostat  of  the  first  cycle  to 
serial clamp X4, connect it to D7 and GND. 

 

3.6.9.2.4 Temperature sensor of the second cycle connection 

 

NOTE 

The  temperature  sensor  for  the  riser  pipe  is  used  as  a  safeguard  of  the  cycle 
and for controlling the mixing valve. 
 

 

 

Connect the riser pipe temperature sensor of 
the second cycle to serial clamp X4, connect 
it to A7 and GND. 

 

3.6.10 

EXTERNAL ADDITIONAL SOURCE CONNECTION 

 

CAUTION 

The  device  can  only  be  connected  with  the  control  signal  for  the  external 
additional  source.  Perform  the  connection  of  the  external  additional  source 
separately. 

 

 

Connect the signal for controlling the external 
additional source (electric heater, oil, pellet 
or gas furnace) to serial clamp X3, connect it 
to terminal  Q12, N and  . 
 

Consider manufacturer

’

s instructions for 

the external additional source when 
connecting the control signal! 

 

Summary of Contents for HM-130 S1





























































Reviews:

No comments

Related manuals for HM-130 S1

Gardena 7000 Operator'S Manual preview
7000
Brand: Gardena Pages: 13
WarmFlow A Series User Instructions preview
A Series
Brand: WarmFlow Pages: 89
Danfoss H1 Series Service Manual preview
H1 Series
Brand: Danfoss Pages: 72
Panasonic WH-MDC05F3E5 Operating Instructions Manual preview
WH-MDC05F3E5
Brand: Panasonic Pages: 100
Panasonic WH-SDC07H3E5 Quick Manual preview
WH-SDC07H3E5
Brand: Panasonic Pages: 88
Panasonic Aquarea WH-MDF09C3E5 Installation Manual preview
Aquarea WH-MDF09C3E5
Brand: Panasonic Pages: 90
Panasonic WH-MDC05J3E5 Operating Instructions Manual preview
WH-MDC05J3E5
Brand: Panasonic Pages: 80
DAB FEKA VS Instructions For Installation, Maintenance And Use preview
FEKA VS
Brand: DAB Pages: 12
DAY 78714 Instruction Manual preview
78714
Brand: DAY Pages: 51
Estate Design AUBURN EFSXB-15ABLK Owner'S Manual preview
AUBURN EFSXB-15ABLK
Brand: Estate Design Pages: 9
HISEER AW13 Technology Manual preview
AW13
Brand: HISEER Pages: 8
Stahls Hotronix Fusion IQ XF Controller Replacement Manual preview
Fusion IQ XF
Brand: Stahls Hotronix Pages: 15
Pinnacle Climate Technologies REMINGTON REM-16-TTC-O User'S Manual & Operating Instructions preview
REMINGTON REM-16-TTC-O
Brand: Pinnacle Climate Technologies Pages: 32
True North TN19 Installation And Operating Instructions Manual preview
TN19
Brand: True North Pages: 20
P.Lindberg 9051422 Original Manual preview
9051422
Brand: P.Lindberg Pages: 26
Neilsen CT5308 Quick Start Manual preview
CT5308
Brand: Neilsen Pages: 8
MILL GL1000LW1R3 Assembly And Instruction Manual preview
GL1000LW1R3
Brand: MILL Pages: 144
Varian TV 301 Navigator 969-8918 Instruction Manual preview
TV 301 Navigator 969-8918
Brand: Varian Pages: 55

Brands by name

Popular brands

Load more brands