Krone Comprima F 125 Original Operating Manual Download Page 182 | Manualshive

Page: 182 / 234

background image

IX - 16

Maintenance

9.3.14 Main Drive Gear Box

The main drive gearbox (1) is located inside the front
cross carrier of the round baler.

Checking the Oil Level

Check the oil level before initial use.
Check the oil in the gearbox after every 500 round bales.
Unscrew the oil check screw (3).
The oil level should reach up to the check hole.

Changing the Gearbox Oil

Gearbox oil should be changed after initial use
(approximately 30 - 50 hours) and at the end of each
season.

To do this:
•

Unscrew the oil screw plug (2)

•

Collect the gearbox oil (approx. 1,7 litres) in a suitable
container.

•

Screw in the oil screw plug (2)

•

Add oil (4) (oil level up to hole) (3) (approx. 1,7 litres of
SAE90 API-GL-4).

9.4

Drive Chains

9.4.1 Special Safety Instructions

The drive chains are equipped with protective devices. Always reattach or close the protective
devices after completing work on the chains.

9.4.2 General Information

Central lubrication only

The chain lubrication device supplies oil to all drive
chains except for the drive chain on the twin twine guide.
As the lubricating oil lines are not subjected to high
pressure, clogging may occur. For this reason, the
lubricating oil lines should be checked before each use to
ensure proper function. How the central chain lubrication
device operates is explained in the "Basic Settings and
Operation" section of this booklet.

Dispose of used oil properly!

RPN00050

4

1

2

3

«
...
180
181
182
183
184
...
»

Summary of Contents for Comprima F 125











































































































































































































































Reviews:

No comments

Related manuals for Comprima F 125

Brand: NORLUX Pages: 2

Brand: Abbott Pages: 2

FreeStyle Libre

Brand: Abbott Pages: 3

Brand: abc Pages: 8

Brand: Hakko Electronics Pages: 8

Professional HS 8

Brand: Hailo Pages: 5

Brand: Hainbuch Pages: 52

Brand: NatureZap Pages: 2

ProFire Lightbridge

Brand: M-Audio Pages: 8

Brand: M-Audio Pages: 36

Brand: York Pages: 26

Brand: PASCO Pages: 30

Brand: Qiagen Pages: 48

Brand: Qiagen Pages: 162

Brand: Qazqa Pages: 4

Brand: Qlightec Pages: 12

LUNAQUA Classic LED

Brand: Oase Pages: 16

Brand: Milestone Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands