Krone Comprima F 125 Original Operating Manual Download Page 212

Page: 212 / 234

A - 8

Appendix

Adjust drawbar height.
•

Slacken the self-locking nuts (3) until you can turn the
drawbar (1) inside the toothed disk connection.

•

Adjust the drawbar (1) to the height of the tractor hitch.

•

Undo screw connection (4).

•

Align the ring hitch (2) horizontally (parallel to the
ground).

•

Tighten screw connections (3) and (4) with the required
torque.

The toothed disks (5) must mesh.
Tighten the screw connections again after
10 operating hours!

A1.3 Adjusting Drawbar Height

To ensure optimum pick-up of baling material, the drawbar
height must be adapted to the type of tractor being used.

When hitched up, dimension x measured between the
centre of the cutting roller and the ground should be x =
700 mm, for use with straw up to 800 mm.

RPN00068

RPN00063

Summary of Contents for Comprima F 125











































































































































































































































Search results

Summary of Contents for Comprima F 125

Reviews:

Related manuals for Comprima F 125

Brands by name

Popular brands

Krone Comprima F 125, Original Operating Manual

Search results

Summary of Contents for Comprima F 125

Reviews:

Related manuals for Comprima F 125

Brands by name

Popular brands