Krone Comprima F 125 Original Operating Manual Download Page 96

Page: 96 / 234

KRONE ISOBUS-Terminal CCI 100

VI - 20

6.7.2

Menu 1-4 “Sensitivity of the direction display”

CC000211

1-4

Fig.20
Setting the sensitivity of the direction display
Displaying the menu

Main menu 1 “Settings” is displayed.

•

You can select menu 1-4

by pressing function key

. The symbol is shown in

reverse colours

•

Press function key

The display shows menu 1-4 “Sensitivity of the direction display”.

The progress bar indicates the set sensitivity. The higher the bar, the greater the sensitivity of the

direction display. The symbol

in the upper line indicates that the displayed value is saved.

Setting and saving the sensitivity of direction display (Comprima F125/F155).

The higher the sensitivity of the direction display is set, the stronger the motion indication in the form

of arrows (1) (

)

•

Set the sensitivity with the function key

, the symbol

in the top line goes out

•

Press the function key

. The set sensitivity is saved and the symbol

appears in the upper

line

•

Pressing the function key

closes the called up menu

•

Pressing the function key

and holding it down brings up the basic screen

Summary of Contents for Comprima F 125











































































































































































































































Search results

Summary of Contents for Comprima F 125

Reviews:

Related manuals for Comprima F 125

Brands by name

Popular brands

Krone Comprima F 125, Original Operating Manual

Search results

Summary of Contents for Comprima F 125

Reviews:

Related manuals for Comprima F 125

Brands by name

Popular brands