Krone Comprima F 125 Original Operating Manual Download Page 167 | Manualshive

Page: 167 / 234

background image

IX - 1

Maintenance

9

Maintenance

9.1

Adjustments

9.1.1 Special Safety Instructions

•

The adjustments listed below should be done only when the machine is at a complete
standstill. Switch off the motor, remove the ignition key and disconnect the 12 V supply
voltage.

•

Secure the tractor and round baler against rolling.

•

After completing maintenance work, reattach all protective plates and protective devices
properly.

•

Follow all further safety instructions, to avoid accidents and injuries.

After the setting is made, run the round
baler manually and check whether the
scraper rail (6) comes in contact with the
spiral roller (2).

If the scraper rail is not resting against the
spiral roller, the clamping wedge (5) can be
turned 180°. (The dimensions of the
clamping lever from the oblong hole to the
upper and lower stop edges are different).

The scraper rail (6) is adjusted relative to
the upper spiral roller inside the bale
chamber. Make certain to close the shut-off
tap (1) on the left-hand tailgate hydraulic
cylinder after opening the bale chamber
positon <b>.

9.1.2 Adjusting the Scraper Bar In Relation

to the Upper Spiral Roller

•

Install the scraper bar (7) so it is centred in the oblong
hole of the side part and slightly tighten the screws.

•

Drive the clamping wedge (5) tightly into place and
tighten the screws securely.

•

Move the scraper rail (6) up against the spiral roller (2).

•

Then tighten the hexagonal head screws (3) and
threaded rods.

RPN00064_2

4

5

2

7

6

3

b

a

1

RPN00016_1

1

«
...
165
166
167
168
169
...
»

Summary of Contents for Comprima F 125











































































































































































































































Reviews:

No comments

Related manuals for Comprima F 125

Brand: Bartscher Pages: 22

Brand: Omnia Pages: 8

Brand: GE Pages: 212

Brand: Garelick Pages: 2

Brand: Gardico Pages: 2

Brand: OceanSat Pages: 85

AquaPure Ei Series

Brand: Jandy Pages: 4

AquaPure Ei Series

Brand: Jandy Pages: 8

Jandy Pro Series

Brand: Jandy Pages: 16

Brand: Zimmer Pages: 2

Brand: ZipRip Pages: 31

Brand: GE Pages: 37

Brand: MacDon Pages: 238

Brand: stilum Pages: 4

Brand: ZAMST Pages: 14

Brand: Future Artist Pages: 42

LED Niova 150-F Pro 150W Bi Color

Brand: Walimex Pro Pages: 56

Brand: Sport-thieme Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands