Kollmorgen AKD series Installation Manual Download Page 208 | Manualshive

Page: 208 / 216

background image

AKD Installation | 10 Setup

10.4.3 Additional error and alarm messages AKD-M

Faults/Errors and Warnings/Alerts are displayed in the 7 segment displays of the drive:

AKD two digits

AKD-M two + one digits

The two digits LED display indicates
the drive messages.
Drive fault messages are coded with
"F", warnings are coded with "n" and
are described in (

The one digit LED indicates the PDMM
messages of the AKD PDMM.
Error messages are coded with "E",
alarms are coded with "A" and are
described in the chapter below.

To simplify handling, the error and alarm handling process is consistent, so you can always
apply the same recovery steps. When an error or alarm occurs, it is displayed to the one digit
display, you can identify the error in the table below and follow the recommendations to fix
the problem, clear the display, and resume machine operation.

Active errors and alarms can be cleared with the controller command

ClearCtrlErrors

,

(Note: non-clearable errors will remain).

10.4.3.1 Alarms

Alarm Description

A01

High temperature exceeded

A02

Low on memory.

A04

Low input voltage

A12

Flash memory is low on free space.

A21

Recoverable process or thread failed to respond during operation.

A23

CPU is overloaded

A30

EtherCAT missed a send frame during operation mode.

A38

EtherCAT missed a receive frame during operation mode.

A40

Local digital IO missed a cyclic update

A53

AKD-M-MC was replaced with the higher performance M1 model.

208

Kollmorgen | kdn.kollmorgen.com | October 2017

«
...
206
207
208
209
210
...
»

Summary of Contents for AKD series

























































































































































































































Reviews:

No comments

Related manuals for AKD series

Brand: NAD Pages: 39

Brand: Yamaha Pages: 84

Brand: Broadcast Tools Pages: 5

Brand: Audio Research Pages: 8

Brand: Carson Pages: 12

EVID C8.2 Ceiling

Brand: Electro-Voice Pages: 2

Brand: Wilson Electronics Pages: 6

Brand: Omron Pages: 16

DANTE VIRGIL OB

Brand: Glensound Pages: 26

Brand: Hyundai Pages: 17

Brand: Parasound Pages: 14

redback A 4140 2 x 100W

Brand: Altronics Pages: 4

ATLONA AT-RON-442

Brand: Panduit Pages: 12

Brand: SAL Pages: 40

Brand: Marantz Pages: 17

Brand: PrimaLuna Pages: 20

POWER 400 - POWER 400 AMPLIFIER

Brand: Jensen Pages: 44

Brand: NAIM Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands