Kollmorgen AKD series Installation Manual Download Page 108 | Manualshive

Page: 108 / 216

background image

AKD Installation | 9 Electrical Installation

9.9 DC Bus link (X3, X14)

The DC bus link can be connected in parallel so that the regen power is divided between all
the drives that are connected to the same DC bus link circuit. Every drive must have it's own
power connection to mains voltage, even if the DC bus link is used. Drives working gen-
eratively very often should be placed beside drives, which need energy. That reduces current
flow on longer distances. For fuse type definition refer to (

The sum of the rated currents for all of the drives connected in parallel to an

AKD-x003 to

024

must not exceed 48 A.

Use 6 mm², unshielded single cores with a max. length of 200 mm; use 6 mm² shielded
cables for longer lengths. In this case no fuse for line protection is required.
The sum of the rated currents for all of the

AKD-x048

connected in parallel to an AKD-

x048 must not exceed 96 A. AKD-x048 should be connected in parallel only with AKD-
x048 drives. Use 16 mm², unshielded single cores with a max. length of 30 mm; use
16 mm² shielded cables for longer lengths.

The drives can be destroyed, if DC bus link voltages are different. Only drives with mains
supply from the same mains (identical mains supply voltage) may be connected by the DC
bus link. DC bus link connection of AKD-x048 to other drives than AKD-x048 is not allowed.

The phase lost/ main control is not working on DC-Bus connected drives. A phase lost on a
drive inside a DC Bus connection will be not detected. External phase monitoring to prevent
overload of the rectifier is recommended.

AKD-x00306 to AKD-x00606 (X3)

Pin

Signal

Description

2

-DC

DC-Link Bus negative

3

+DC (+RB) DC-Link Bus positive

AKD-x01206 (X3)

Pin

Signal

Description

3

-DC

DC-Link Bus negative

4

+DC (+RB) DC-Link Bus positive

AKD-x02406 & AKD00307 to AKD02407 (X3)

Pin

Signal

Description

3

-DC

DC-Link Bus negative

4

+DC (+RB) DC-Link Bus positive

AKD-x04807 (X14)

Pin

Signal

Description

1

-DC

DC-Link Bus negative

2

n.c.

not connected

3

+DC

DC-Link Bus positive

NOTE: Should be connected in parallel only with AKD-x048
drives.

108

Kollmorgen | kdn.kollmorgen.com | October 2017

«
...
106
107
108
109
110
...
»

Summary of Contents for AKD series

























































































































































































































Reviews:

No comments

Related manuals for AKD series

Brand: NAD Pages: 2

MINAS-BL GP series

Brand: Panasonic Pages: 56

Brand: Opus Technologies Pages: 36

Brand: Crate Pages: 8

Brand: ORANGE Pages: 13

Super Blue PB559X

Brand: Pyramid Pages: 12

Brand: Glensound Pages: 15

Brand: COMMERCIAL AUDIO Pages: 17

Axiom HPD3400PFC

Brand: PROEL Pages: 24

Brand: Fender Pages: 18

Brand: DAPAudio Pages: 14

Brand: Sansui Pages: 32

Brand: FONESTAR Pages: 9

Brand: Acoustic Pages: 8

Brand: audiophony Pages: 5

Brand: M-system Pages: 4

Brand: Audio Research Pages: 9

IMG STAGE LINE 25.3250

Brand: Monacor Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands