Kollmorgen AKD series Installation Manual Download Page 202 | Manualshive

Page: 202 / 216

background image

AKD Installation | 10 Setup

10.4 Fault and Warning Messages

10.4.1 Fault and warning messages AKD

When a fault occurs, the drive fault relay is opened, the output stage is switched off (motor
loses all torque), or the load is dynamically braked. The specific drive behavior depends on
the type of fault. The LED display on the front panel of the drive shows the number of the fault
that occurred. If a warning is issued prior to the fault, the warning is shown on the LED and
has the same number as the associated fault. Warnings do not trip the power stage of the
drive or fault relay output.

AKD fault codes or warning codes are displayed constantly if present. Fault
messages are coded with "F", warnings are coded with "n".
With built-in I/O option card, SD card operation errors are displayed with "E" fol-
lowed by 4 digits.

The left side of the LED displays F (or E) for a fault or n for a warning. The right side displays
the fault or warning number as follows: 1-0-1-[break]. The highest priority fault is displayed.
Multiple faults may be present when a fault condition is occurring. Check the AKD
WorkBench Fault Screen or read the status of DRV.FAULTS through the controller or HMI
for the entire list of faults.

Eliminate errors and faults in compliance with work safety rules. Troubleshooting only by
qualified and trained staff.

More information about fault messages, remedy and clearing faults can be found in the
WorkBench online help and in

Code

Message/Warning

..

24V power (X1) overload or 5V (X9) shorted

F0

Reserved.

F101, n101

Firmware incompatible. The FPGA is a laboratory FPGA.

F102, n102

Resident firmware failed. Operational FPGA is not a default FPGA.

F103

Resident FPGA failed.

F104

Operational FPGA failed.

F105

Non-volatile memory stamp invalid.

F106

Non-volatile memory data.

n107

Positive limit switch triggered.

n108

Negative limit switch triggered.

F120

Failed to default parameters.

F121

Homing error.

F123, n123

Invalid motion task.

F124

Cogging Compensation non volatile memory data error (CRC).

F125, n125

Fieldbus synchronization frames lost.

F126, n126

Bode plot: too much movement.

F127

Incomplete emergency procedure.

F128

MPOLES/FPOLES not integer.

F129

Fieldbus Heartbeat lost.

F130

Secondary feedback supply over current.

F131

Secondary feedback A/B line break.

F132

Secondary feedback Z line break.

F133

Fault number changed to F138.

202

Kollmorgen | kdn.kollmorgen.com | October 2017

«
...
200
201
202
203
204
...
»

Summary of Contents for AKD series

























































































































































































































Reviews:

No comments

Related manuals for AKD series

Brand: Aaron Pages: 2

Brand: QUAD Pages: 4

Brand: QSC Pages: 142

Brand: Warwick Pages: 11

Brand: DAPAudio Pages: 15

Brand: Soundstream Pages: 10

Brand: Technics Pages: 19

Brand: Redback Pages: 4

Brand: HBM Pages: 102

Brand: Optimus Pages: 24

Brand: Laney Pages: 12

Brand: NAD Pages: 22

Brand: Ibiza sound Pages: 24

KICKSTART 25 DSP

Brand: Carlsbro Pages: 4

Brand: IED Globalcom Pages: 20

Brand: Redback Pages: 2

Brand: DaytonAudio Pages: 16

Brand: ifi Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands