33
3
UM 11 LD 625-3_626-3 _ cod. ED0053030990 -
1° ed
_rev.
00
be filled with oil.
•
Since the oil must be emptied out while the engine is still
hot (approx. 80°C), particular care should be taken in order
to avoid burns. In any case make sure that oil does not
come into contact with your skin because of the health
hazards involved.
•
Fuel vapours are highly toxic, so fill up only in the open
air or in well ventilated environments.
•
During operations which involve access to moving
parts of the engine and/or removal of the rotary guards,
disconnect and insulate the positive cable of the battery
so as to prevent accidental short circuits and activation
of the starter motor.
•
Check the belt tension only when the engine is turned off.
IMPORTANT
•
To start the engine follow the specific instructions provided
in the engine and/or machine operating manual. Do not
use auxiliary starting devices not originally installed on the
machine (e.g. Startpilot systems which utilise ether etc.)
•
Before carrying out any work on the engine, turn it off and
allow it to cool down. Do not perform any operation while
the engine is running.
•
Check that the discharged oil, the oil filter and the oil
contained in the oil filter are disposed of in such a way as
not to harm the environment.
•
Close the fuel tank filler cap carefully after each fílling
operation. Do not fill the tank right up to the top, but leave
sufficient space to allow for any expansion of the fuel.
•
Do not smoke or use naked flames while filling.
•
Take care when removing the oil filter as it may be hot.
•
The operations of checking, filling up and replacing the
cooling liquid must be carried out with the engine turned
off and cold. Take particular care if liquids containing
nitrites are mixed with others not containing these
compounds as this may give rise to the formation of
nitrosamines which are a health hazard. The cooling
liquid is polluting, so dispose of in a manner that does not
damage the environment.
•
In order to move the engine simultaneously use the
eyebolts fitted for this purpose by
Lombardini
. These
lifting points are however not suitable for the entire
machine, so in this case use the eyebolts fitted by the
manufacturer.
NORME DI SICUREZZA - NORMES DE SÉCURITÉ - SAFETY REGULATIONS
SICHERHEITSVORSCHRIFTEN - NORMAS DE SEGURIDAD - NORMAS DE SEGURANÇA
Summary of Contents for Lombardini 3 LD 450
