Kodak HEALTH SCIENCES X-Omat Clinic 1 Installation Instructions Manual Download Page 66

Page: 66 / 76

INSTALLATION INSTRUCTIONS

September 1995 – 981088

Section 13: Installing the FEED TRAY

[1] Check that the FRONT ACCESS PANEL is installed on the PROCESSOR.

[2] Align the FEED TRAY so that it is flush with the FRONT ACCESS PANEL on the PROCESSOR.

[3] Install the following parts that secure the FEED TRAY onto the PROCESSOR:

• 2 SCREWS

• 2 LOCK WASHERS

• 2 WASHERS

Figure 57

Installing the FEED TRAY

Section 14: Installing the LIGHTTIGHT FEED TRAY

If you plan to install a LIGHTTIGHT FEED TRAY, see the Installation Instructions, Publication Number 1C0937,
provided with the kit.

H130_0084BA

H130_0084BCA

LOCK WASHER (2)

WASHER (2)

FEED TRAY

SCREW (2)

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1













































































Search results

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1

Reviews:

Related manuals for HEALTH SCIENCES X-Omat Clinic 1

Brands by name

Popular brands

Kodak HEALTH SCIENCES X-Omat Clinic 1, Installation Instructions Manual

Search results

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1

Reviews:

Related manuals for HEALTH SCIENCES X-Omat Clinic 1

Brands by name

Popular brands