manualshive.com logo in svg

Kodak HEALTH SCIENCES X-Omat Clinic 1, Installation Instructions Manual

Share
Download
Kodak HEALTH SCIENCES X-Omat Clinic 1 Installation Instructions Manual Download Page 24

INSTALLATION INSTRUCTIONS

24

September 1995 – 981088

Routing the REPLENISHMENT HOSES

If the REPLENISHMENT TANKS are inside the darkroom, you need to route the REPLENISHMENT
HOSES through the darkroom wall.  Do Steps 46 through 48.  If you do not need to route the REPLENISHMENT
HOSES through the darkroom wall, advance to Step 49 on Page 25.

[46] Connect the 2 black, opaque

3

⁄

8

in. REPLENISHMENT HOSES provided in the THROUGH-THE-WALL KIT

to the clear REPLENISHMENT HOSES coming from the PROCESSOR.

Figure 19

Connecting the REPLENISHMENT HOSES

Note

When routing the HOSES through the MOUNTING STAND:

• check that you do not interchange the position of the HOSES between where they enter the MOUNTING

STAND and where they pass through the wall

• install the REPLENISHMENT HOSES with slack in the HOSES

• note that the developer REPLENISHMENT HOSE has a red WIRE TIE for easy identification

• note that the fixer REPLENISHMENT HOSE has a blue WIRE TIE for easy identification

• install the DRAIN HOSES without slack in the HOSES

[47] Route the following HOSES through the holes in WOOD FRAME, as needed:

• 3 DRAIN HOSES

• HOSE from the main water supply

• 2 REPLENISHMENT HOSES

[48] If you do not need to route the REPLENISHMENT HOSES through the darkroom wall, continue with the steps

below  Otherwise, advance to Step 51 on Page 25.

H130_0112HA

red

TIE

(2)

FITTING

H130_0112HCB

fixer

developer

HOSE

REPLENISHMENT

HOSE

REPLENISHMENT

blue WIRE TIE

WIRE

fixer
DRAIN VALVE

STEM

WATER INPUT

SOLENOID

developer
DRAIN VALVE

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands