manualshive.com logo in svg

Kodak HEALTH SCIENCES X-Omat Clinic 1, Installation Instructions Manual

Share
Download
Kodak HEALTH SCIENCES X-Omat Clinic 1 Installation Instructions Manual Download Page 53

Making the Necessary Connections

981088 – September 1995

53

Connecting the HOSES from the REPLENISHMENT TANKS
in Table Top or MOUNTING STAND Installations

[1] Check that all 3 DRAIN VALVES are closed.

[2] Remove the tape securing the REPLENISHMENT HOSES.

Note

If you are installing the PROCESSOR through the darkroom wall, see “Installing the PROCESSOR Through the
Wall” on Page 13.

[3] Route the REPLENISHMENT HOSES through the HOLES in the base of the PROCESSOR.

Note

• HOSES for connecting the REPLENISHMENT TANKS to the REPLENISHMENT HOSES on the

PROCESSOR are not packed with the PROCESSOR.  Use standard

3

⁄

8

-in. tubing.

• Use a small HOSE CLAMP (provided with M43 and M43A only).

• The FITTING on the fixer REPLENISHMENT HOSE has a blue WIRE TIE for easy identification.

The FITTING on the developer REPLENISHMENT HOSE has a red WIRE TIE for easy identification.

Figure 45

Connecting the REPLENISHMENT HOSES

[4] Connect the fixer REPLENISHMENT HOSE on the PROCESSOR to the fixer REPLENISHMENT TANK.

[5] Install a STRAINER ASSEMBLY in the fixer REPLENISHMENT HOSE near the REPLENISHMENT

TANK.

[6] Connect the developer REPLENISHMENT HOSE to the developer REPLENISHMENT TANK.

[7] Install a STRAINER ASSEMBLY in the developer REPLENISHMENT HOSE near the REPLENISHMENT

TANK.

H130_0112HA

red

TIE

(2)

FITTING

H130_0112HCB

fixer

developer

HOSE

REPLENISHMENT

HOSE

REPLENISHMENT

blue WIRE TIE

WIRE

fixer
DRAIN VALVE

STEM

WATER INPUT

SOLENOID

developer
DRAIN VALVE

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands