manualshive.com logo in svg

Kodak HEALTH SCIENCES X-Omat Clinic 1, Installation Instructions Manual

Share
Download
Kodak HEALTH SCIENCES X-Omat Clinic 1 Installation Instructions Manual Download Page 7

Unpacking the PROCESSOR

981088 – September 1995

7

Figure 3

Unpacking the RACKS

[5] Remove the 2 SCREWS securing the WOOD RESTRAINT on the DEVELOPER RACK.  Remove the WOOD

RESTRAINT from the DEVELOPER RACK.

[6] Remove the 2 SCREWS securing the WOOD RESTRAINT on the FIXER RACK.  Remove the WOOD

RESTRAINT from the FIXER RACK.

[7] Locate the SCREW hole on the drive side of the PROCESSOR that was used to secure the WOOD

RESTRAINT onto the FIXER RACK.

[8] Install the O-RING provided into that hole using the SCREW and WASHER provided.  The O-RING will be

used in later procedures to enable you to secure the COVER of the ELECTRICAL BOX in the open position.
See the figure.

[9] Remove the DEVELOPER and FIXER RACKS and any protective packing material.

[10] Cut and remove the STRAP securing the WASH RACK in place.

[11] Remove any remaining protective packing material.

H130_0170DA

DRIVE

ACCESS

PANEL

SIDE

STRAP

O-RING

WASHER

SCREW

WOOD RESTRAINTS

H130_0170DCA

DEVELOPER
RACK

FIXER RACK

WASH RACK

SCREWS (4)

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands