Kodak HEALTH SCIENCES X-Omat Clinic 1 Installation Instructions Manual Download Page 31

Page: 31 / 76

Installing the PROCESSOR

981088 – September 1995

Installing the KNOBS

[83] Install the KNOBS for the DRAIN VALVES by doing the steps below:

(a) Check that all 3 DRAIN VALVES are closed.

(b) Install the 3 KNOBS.

Check that you align the SETSCREW of the KNOB with the flat section of the STEM.

Leave a 3 mm (

⁄

in.) gap between the FRONT ACCESS PANEL and the back of the KNOBS.

Secure the KNOBS using the 2 SETSCREWS provided for each.

Figure 25

Installing the KNOBS for the DRAIN VALVES

[84] Install the DRYER TEMPERATURE CONTROL KNOB.

(a) Align the SETSCREW of the KNOB with the flat section of the STEM.

(b) Press the DRYER TEMPERATURE CONTROL KNOB onto the STEM of the DRYER

TEMPERATURE CONTROL.

(c) Check that the DRYER TEMPERATURE CONTROL KNOB is not touching the FRONT ACCESS

PANEL.

[85] Advance to “Doing the Water Leak Test” procedure on Page 54.

Figure 26

Installing the DRYER TEMPERATURE CONTROL KNOB

H130_0149AA

PANEL

FRONT ACCESS

H130_0149ACA

KNOB (3)

SETSCREW
(2)

STEM (3)

Ready

Wait

Service

Dryer

Temperature

H130_0003AA

DRYER TEMPERATURE
CONTROL KNOB

H130_0003ACB

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1













































































Search results

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1

Reviews:

Related manuals for HEALTH SCIENCES X-Omat Clinic 1

Brands by name

Popular brands

Kodak HEALTH SCIENCES X-Omat Clinic 1, Installation Instructions Manual

Search results

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1

Reviews:

Related manuals for HEALTH SCIENCES X-Omat Clinic 1

Brands by name

Popular brands