manualshive.com logo in svg

Kodak HEALTH SCIENCES X-Omat Clinic 1, Installation Instructions Manual

Share
Download
Kodak HEALTH SCIENCES X-Omat Clinic 1 Installation Instructions Manual Download Page 52

INSTALLATION INSTRUCTIONS

52

September 1995 – 981088

[4] Check that the Water Usage Mode is correct.  Refer to Table 1, “Setup Options” on page 37.  The PROCESSOR

is factory set for Continuous Water Usage Mode.  In this mode, water runs at one litre per minute.  This allows
fresh water to circulate through the PROCESSOR and prevent biological growth.  If biological growth is not a
concern, the PROCESSOR may be set to Low Water Usage Mode.

Note

If Low Water Usage Mode is configured, the WASH WATER DRAIN VALVE must be changed.  A white dot on
the WASH WATER VALVE STEM indicates a valve with an oraface, which is used for Continuous Wash Mode
only.   Refer to “Replacing the Drain Valves,” Plumbing Section in the Service Manual.

Note

If you are routing a water supply HOSE under the PROCESSOR, you will need a 90

°

 fitting, not provided, at the

WATER INPUT SOLENOID connection.

Figure 44

Connecting the DRAIN HOSES and the HOSE from the Main Water Supply

H130_0026BA

fixer DRAIN HOSE

wash DRAIN HOSE

water supply HOSE

developer DRAIN HOSE

BIB FITTING

SOLENOID

WATER INPUT

H130_0026BCB

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands