manualshive.com logo in svg

Kodak HEALTH SCIENCES X-Omat Clinic 1, Installation Instructions Manual

Share
Download
Kodak HEALTH SCIENCES X-Omat Clinic 1 Installation Instructions Manual Download Page 55

Doing the Water Leak Test

981088 – September 1995

55

Figure 47

Checking for Leaks Behind the

ELECTRICAL BOX

[4] Check that the PROCESSOR is still level when it

is full of solution.  See the procedure on Page 47.
Leveling the PROCESSOR correctly will ensure:

• the correct flow of the processing solutions

• the correct transport of the film

• the correct fit of all ACCESS PANELS

[5] Check for leaks at all connections.  Tighten HOSE

CLAMPS as necessary.

[6] Pull out the SUPPORT SHELF for the

ELECTRICAL BOX from the drive side of the
PROCESSOR.

[7] Pull out the ELECTRICAL BOX.

[8] Using a FLASHLIGHT, check for leaks behind

the ELECTRICAL BOX.  Tighten HOSE
CLAMPS, as necessary.

[9] Push the SUPPORT SHELF and the

ELECTRICAL BOX to their original positions.

[10] Turn on the main water supply to the

PROCESSOR.

Warning

Dangerous Voltage

[11] Connect the main power to the PROCESSOR.

[12] Rotate the DRYER TEMPERATURE

CONTROL KNOB on the DISPLAY PANEL
fully counterclockwise

.

Figure 48

Identifying Components

on the DISPLAY PANEL

H130_0151CA

SHELF

SUPPORT

H130_0151CCA

ELECTRICAL
BOX

+

-

Ready

Wait

Service

Dryer

Temperature

H130_0003AA

H130_0003ACE

CONTROL KNOB

DRYER TEMPERATURE

BREAKER CB1

MAIN CIRCUIT

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands