Kodak DryView 8150 User Manual Download Page 78

Page: 78 / 178

2-44

7F3319

October 4, 2004

Operation and Maintenance

If the modality does not respond to the

Ping

, a message screen informs of

the failure

PM (Preventive Maintenance)|
Service Menu Choice

This menu choice performs two functions: Selecting

on the Service

Screen displays the screen below.

• Enters the current date into the Service History log as the date of a PM

session.

• Resets the "Prints to PM" counter to zero. This counter records the

number of films of each size printed since the last PM.

You must have the Customer First passcode to perform this operation.
When you select

on the Service Screen, the following screen appears.

Select

Yes

to continue. Enter the Customer First passcode on the keypad

that follows.

Summary of Contents for DryView 8150



















































































































































































Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands

Kodak DryView 8150, User Manual

Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands