Kodak DryView 8150 User Manual Download Page 98

Page: 98 / 178

2-64

7F3319

October 4, 2004

Operation and Maintenance

Setting Time and Date

The time and date appear in the

Home

screen.

The

time

time format

date

and

date format

can be set. The Service

Passcode is required.
The combination of date and time can be increased or decreased by no
more than 24 hours.

• Formats for time include AM/PM or 24-hour (military).

• Formats for date include

– MM_DD_YYYY

– DD_MM_YYYY

– YYYY_MM_DD

To change the time, time format, date or date format:

1. Touch the

Menu

button.

2. Touch

Setup Imager

3. You will see a prompt to start the

Installation Assistant

. Select

Date and Time

Summary of Contents for DryView 8150



















































































































































































Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands

Kodak DryView 8150, User Manual

Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands