Kodak DryView 8150 User Manual Download Page 54

Page: 54 / 178

2-20

7F3319

October 4, 2004

Operation and Maintenance

System Functions Screen

This screen provides two functions:

• Users who have logged on with a passcode can log off from this screen.

• Operators can set the Imager either

online

offline

When

online

, the Imager is connected to the network and can

receive images from the associated modalities.

When

offline

, the Imager is temporarily disconnected from the

network and cannot receive images but jobs in the print queue will
continue printing.

To display this screen:

Menu

System Functions

Imager online/offline button

This button toggles between

online

and

offline

. When offline, the

Imager is temporarily disconnected from the network and cannot
receive images.

Online/Offline Indicator

Green indicates

online

, yellow indicates

offline

Logoff button.

If you have logged on with any passcode, touch

this button to log off. This will prevent unauthorized use of
passcode-protected functions.

Summary of Contents for DryView 8150



















































































































































































Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands

Kodak DryView 8150, User Manual

Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands