Kodak DryView 8150 User Manual Download Page 7 | Manualshive

Page: 7 / 178

background image

October 4, 2004

7F3319

5

State Street, Rochester, New York, 14650.

END-USER LICENSE
AGREEMENT FOR
MICROSOFT DESKTOP
OPERATING SYSTEMS

IMPORTANT-READ CAREFULLY: THIS END-USER LICENSE AGREEMENT
("EULA") IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN
INDIVIDUAL OR A SINGLE ENTITY) AND THE MANUFACTURER
("MANUFACTURER") OF THE COMPUTER SYSTEM OR COMPUTER SYSTEM
COMPONENT ("HARDWARE") WITH WHICH YOU ACQUIRED THE
MICROSOFT SOFTWARE PRODUCT(S) IDENTIFIED ABOVE ("SOFTWARE
PRODUCT" OR "SOFTWARE"). IF THE SOFTWARE PRODUCT IS NOT
ACCOMPANIED BY NEW HARDWARE, YOU MAY NOT USE OR COPY THE
SOFTWARE PRODUCT. THE SOFTWARE PRODUCT INCLUDES COMPUTER
SOFTWARE, THE ASSOCIATED MEDIA, ANY PRINTED MATERIALS, AND ANY
"ONLINE" OR ELECTRONIC DOCUMENTATION. THIS EULA IS VALID AND
GRANTS THE END-USER LICENSE RIGHTS ONLY IF THE SOFTWARE
PRODUCT IS GENUINE AND A GENUINE CERTIFICATE OF AUTHENTICITY
FOR THE PRODUCT SOFTWARE IS PROVIDED WITH THE SOFTWARE
PRODUCT. ANY SOFTWARE PROVIDED ALONG WITH THE SOFTWARE
PRODUCT THAT IS ASSOCIATED WITH A SEPARATE END-USER LICENSE
AGREEMENT IS LICENSED TO YOU UNDER THE TERMS OF THAT LICENSE
AGREEMENT. BY INSTALLING, COPYING, DOWNLOADING, ACCESSING OR
OTHERWISE USING THE SOFTWARE PRODUCT, YOU AGREE TO BE BOUND
BY THE TERMS OF THIS EULA. IF YOU DO NOT AGREE TO THE TERMS OF
THIS EULA, MANUFACTURER AND MICROSOFT LICENSING, INC. ("MS")
ARE UNWILLING TO LICENSE THE SOFTWARE PRODUCT TO YOU. IN SUCH
EVENT, YOU MAY NOT USE OR COPY THE SOFTWARE PRODUCT, AND YOU
SHOULD PROMPTLY CONTACT MANUFACTURER FOR INSTRUCTIONS ON
RETURN OF THE UNUSED PRODUCT(S) IN ACCORDANCE WITH
MANUFACTURER'S RETURN POLICIES.

SOFTWARE PRODUCT
LICENSE

The SOFTWARE PRODUCT is protected by copyright laws and international
copyright treaties, as well as other intellectual property laws and treaties.
The SOFTWARE PRODUCT is licensed, not sold. The term "COMPUTER" as
used herein shall mean the HARDWARE, if the HARDWARE is a single
computer system, or shall mean the computer system with which the
HARDWARE operates, if the HARDWARE is a computer system component.

1. GRANT OF LICENSE. This EULA grants you the following rights:

– Software Installation and Use. You may only install, use, access,

display and run one (1) copy of the SOFTWARE PRODUCT on the

«
...
5
6
7
8
9
...
»

Summary of Contents for DryView 8150



















































































































































































Reviews:

No comments

Related manuals for DryView 8150

Brand: KaVo Pages: 16

Brand: Tacx Pages: 2

Brand: C.E. Nierhoff & Co Pages: 7

Brand: Rapid Technic Pages: 152

Brand: xsto Pages: 76

Brand: F&V Pages: 5

Brand: F Care Systems Pages: 2

Brand: NANLUX Pages: 39

Brand: Labelmate Pages: 61

Brand: NanoVibronix Pages: 2

Brand: NanoVibronix Pages: 32

Shapes Hexagons

Brand: Nanoleaf Pages: 27

Marathon Multi600

Brand: Saeyang Pages: 21

Brand: S&C Pages: 11

Brand: Tascam Pages: 3

Brand: Yamaha Pages: 178

Brand: Yamaha Pages: 15

Brand: GE Pages: 194

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands