Kodak DryView 8150 User Manual Download Page 137

Page: 137 / 178

Adding a Modality

October 4, 2004

7F3319

4-13

Selecting Film Type

The Film Type choices are DVB (

DryView

Blue) and DVC (

DryView

Clear).

There is more than one type of

Kodak DryView

DVB film. The DVB choice

applies to all DVB and DVB+ film types.
If the default shown is not correct for this modality, change the value as

follows

1. On the Advanced defaults screen, highlight

Film Type

2. Touch

Select.

The Edit DICOM attribute screen appears.

3. Use the

Select

button to choose the type of film appropriate for this

modality.

4. For most installations

Override modality

should be left at

false

NOTE: If you select

True

for

Override modality

, the

Film Type

set in

step

will take precedence over any film type requested by the

modality.

5. Touch the

Back

arrow to return to the Advanced defaults screen.

Summary of Contents for DryView 8150



















































































































































































Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands

Kodak DryView 8150, User Manual

Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands