Kodak DryView 8150 User Manual Download Page 143

Page: 143 / 178

Adding a Modality

October 4, 2004

7F3319

4-19

Selecting Color
Negotiation

The Imager prints only grayscale images. If a modality has color capability
and a request to print a color image is sent to the Imager, the Imager
software can print a grayscale version of the color image.

1. Touch the

Down

arrow to proceed to the second Advanced defaults

screen.

2. Use the

Select

button to choose

NOTE: If you select

, the Imager will not accept color prints from the

modality. If you select

Yes

, it will print a gray scale version of the

color print.

3. Touch the

Back

arrow to return to the Modality defaults screen.

Summary of Contents for DryView 8150



















































































































































































Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands

Kodak DryView 8150, User Manual

Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands