Kobelco SK35SR-6 Operation Manual Download Page 253

Page: 253 / 296

This indicates the temperature of the engine

coolant. It is available when the starter switch

is in the "ON" position. The temperature is

normal if it falls within the white range. If the

indicator enters the red range, let the engine

low idle until the water cools down to the white

range.

1. Red: Overheat

2. White: Operational

3. Blue: Cold condition (Warm up the engine)

This indicates the remaining volume of fuel.

When the fuel level is low, the pointer points E.

For fuel to use, see "LUBRICANT, FUEL &

COOLANT SPECIFICATIONS" in Chapter 4.

1. White: Operational zone

2. Red: Refill

After starting the engine, usually main screen

(7) is shown as in the right figure.

８

8.1.1

ENGINE COOLANT TEMPERATURE GAUGE

8.1.2

FUEL LEVEL METER

8.1.3

SWITCH PANEL

［

8. OPTIONAL EQUIPMENT

］

8-5

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands