Kobelco SK35SR-6 Operation Manual Download Page 160

Page: 160 / 296

：

Indicates a required periodic inspection or maintenance with the hour meter interval.

：

Indicates a first one time maintenance interval.

○

：

Indicates a required periodic inspection or maintenance interval.

：

See "LUBRICANT, FUEL & COOLANT SPECIFICATIONS" for the detailed specifications of lubricant,

coolant, and fuel, etc.

LLC

：

Our genuine antifreeze/coolant

：

Contact KOBELCO authorized dealer/distributor for inspection and adjustment.

4.10

INSPECTION AND MAINTENANCE CHART

Follow the chart below for recommended intervals of regular inspection and maintenance procedures.

Perform inspection and maintenance according to the calendar time or operation time shown by the

hour meter, whichever comes first.

See the inspection and maintenance procedure mentioned below for details.

Symbols in the Table

Engine (1/2)

When using in dusty environments, the filters and cores need more frequent cleaning. Check their

contamination levels and clean them accordingly.

［

4. INSPECTION AND MAINTENANCE

］

4-18

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands