Kobelco SK35SR-6 Operation Manual Download Page 181

Page: 181 / 296

Check indicator (A) shown in the right figure.

Red or white indicates a low electrolyte level

or low charge. Take appropriate measures so

that the indicator is displayed in blue.

1. Ventilation cap

2. Terminal

3. Terminal cover

A. Indicator

B. Vent hole

C. Blue

D. Red

E. White

F. (Upper limit)

G. (Lower limit)

H. Good

I. Low electrolyte level

J. Low charge

４

4.13

50 HOUR INSPECTION & MAINTENANCE PROCEDURES

Thoroughly read and understand "1. SAFETY PRECAUTIONS" of this manual before performing the

inspection and maintenance.

Follow this section together with 8-hour (daily) inspection and maintenance described in Chapter 4.

4.13.1

INSPECTING AND MAINTAINING BATTERY

Perform the inspection earlier in summertime as the battery electrolyte decreases faster due to high

temperature.

If the battery with a low electrolyte level is used continuously, it will become unusable. Check the

electrolyte level periodically, and if it is lower than the specified level, supply distilled water before

starting the engine (before charging).

INSPECTING AND MAINTAINING BATTERY

Wear protective glasses, long-sleeve shirt and rubber gloves when handling or servicing batteries.

Do not bring a fire near the battery, or the combustible hydrogen gas generated by the battery may

cause explosion.

If the dilute sulfuric acid in the battery is splashed onto the skin or into the the eyes, it causes

burns or blindness. At such case, immediately wash the skin or eyes with sufficient clean water, and

ask a special doctor to treat it as soon as possible.

Before performing inspection and maintenance on the battery, be sure to stop the engine.

When removing the battery terminal, remove the ground side (negative terminal) first and conversely,

when attaching the battery terminal, attach the ground side last.

Do not put tools and hardware on the protective cover at installed on the battery upper section.

It may cause a short circuit resulting in a fire or explosion.

Indicator

［

4. INSPECTION AND MAINTENANCE

］

4-39

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands