Kobelco SK35SR-6 Operation Manual Download Page 93

Page: 93 / 296

Insert the starter key into the keyway.

Turn the starter key counterclockwise and

pull the door handle to open the door.

If the door is provided with a stay, support

the door securely using the stay.

・

If a stay is provided, return the stay to

the original position.

・

Close the door.

・

Turn the starter key clockwise and remove

it.

・

When you turn the starter key clockwise,

the lock is released and you can open the

side cover.

・

When you close the side cover, it is

automatically locked.

２

2.12.3

GUARD AND SIDE COVER (WITH LOCK LEVER)

Be sure to stop the engine before opening the engine hood or side cover.

The engine hood, fuel inlet, right side cover and cab door (option) are provided with the lock

mechanism. To open/close them, use the starter key.

When using the starter key, fully insert it and then turn it. If it is not fully inserted, it may be broken.

HOW TO UNLOCK AND OPEN GUARD

HOW TO LOCK GUARD

HOW TO OPEN/CLOSE SIDE COVER

［

2. MACHINE FAMILIARIZATION

］

2-29

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands