Kobelco SK35SR-6 Operation Manual Download Page 100

Page: 100 / 296

When the engine is not running, turn starter

switch (1) to the "ON" position to turn on

the monitor panel.

Check fuel level meter (2) for shortage. If

shorted, open the right side cover and

then remove filler cap (3) of the fuel tank.

Fill the fuel tank with the fuel through the

filler port.

For fuel (capacity) to use, see

"LUBRICANT, FUEL & COOLANT

SPECIFICATIONS" in Chapter 4.

When dirt is adhered on strainer (4), take

out the strainer, wash it with light oil or

clean it with air gun, and then fit it to the

filler port again.

After refilling, tighten filler cap (3) securely.

Close the hydraulic oil tank cover and lock

it with the starter key to finish the work.

3.2.3

CHECKING FUEL LEVEL AND MAKING UP

MAKING UP

Use the light oil only. Check the fuel type again before refilling.

Be sure to stop engine before refilling.

Do not overflow fuel while refilling. Wipe off spilled fuel to prevent a fire.

Refill the fuel tank to the maximum after finishing work for a day.

［

3. MACHINE OPERATION

］

3-6

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands