Kobelco SK35SR-6 Operation Manual Download Page 198

Page: 198 / 296

Stop the engine, and open the engine hood.

By using the fuel filter wrench, turn filter

cartridge (1) to the left to remove it.

Wipe the sealing surface of the filter base

with a clean cloth to prevent dust and

foreign materials from being seized.

Apply a thin film of clean engine oil to

packing (A) of new filter cartridge, tighten

it by hand, and then tighten an additional

two-thirds of a turn.

Bleed air according to "BLEEDING AIR

FROM FUEL SYSTEM" in Chapter 4.

Start the engine, run it at idle for several

minutes, and then check the filter

mounting area for fuel leakage.

4.15

500 HOUR (6-MONTH) INSPECTION & MAINTENANCE

PROCEDURES

Thoroughly read and understand "1. SAFETY PRECAUTIONS" of this manual before performing the

inspection and maintenance.

Follow this section together with daily, 50-hour and 250-hour inspection and maintenance.

4.15.1

REPLACING FUEL FILTER

Immediately after the engine is stopped, each part is heated. Wait for them to cool down.

Wipe off spilled fuel to prevent a fire.

The oil filter cannot be reused because it is a cartridge type. Also, it cannot be disassembled for

internal cleaning. Replace it by the set.

［

4. INSPECTION AND MAINTENANCE

］

4-56

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands