Kobelco SK35SR-6 Operation Manual Download Page 173

Page: 173 / 296

Engage the rubber track shoe with the

sprocket and place it on the idler.

Rotate the sprocket in the reverse

direction slowly to push the rubber track

shoe and stop the rotation.

Put in iron pipes along the rubber track

shoe and slowly rotate the sprocket in the

reverse direction again to place the rubber

track shoe on the idler securely.

1. Iron pipe

A. Rotation direction

Stop the rotation and check that the

rubber track shoe is securely placed on the

sprocket, idler and lower roller (1).

Inspect and adjust the tension of rubber

track shoe (2), following "INSPECTING AND

MAINTAINING TRACK SHOE TENSION".

Place the machine on the ground after

checking that tension and engagement

between the rubber track shoe (2), sprocket

(3) and idler (4) is sufficient.

1. Lower roller

2. Rubber track shoe

3. Sprocket

4. Idler

5. Lug

6. Core metal

7. Travel motor

４

［

4. INSPECTION AND MAINTENANCE

］

4-31

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands