Kobelco SK35SR-6 Operation Manual Download Page 69

Page: 69 / 296

Symbol

Item

Name

Engine coolant temperature gauge

Fuel level meter

Engine oil pressure lamp

Engine coolant temperature lamp

Battery charge lamp

Fuel level lamp

Travel in HIGH (2nd) speed lamp

This indicates the temperature of the engine

coolant. The operating temperature is normal if

it falls within the white range. If the pointer

enters the red range, let the engine run at low

idle until the water cools down and the pointer

returns to the white range.

1. White

2. Red

3. Blue

２

2.3

MONITOR PANEL

The monitor consists of the following three parts.

When the warning lamp is lit, stop the work immediately, and inspect and maintain the failure part. For

inspection and maintenance, see the section for inspection and maintenance.

2.3.1

ENGINE COOLANT TEMPERATURE GAUGE

［

2. MACHINE FAMILIARIZATION

］

2-5

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands