Kobelco SK35SR-6 Operation Manual Download Page 39

Page: 39 / 296

・

Do not smoke nor use a fire in the areas

where flammable materials are stored

and/or handled.

・

Refuel only after stopping the engine.

・

Do not leave the machine during refilling

and refilling oil.

・

Be sure to close the fuel and oil filler caps

securely.

・

Watch out not to spill fuel on a heated

surface nor on electrical parts.

・

Store fuel and oil in a designated store

house where only authorized personnel

can go in.

・

After refueling and refilling oil, wipe off

spilled fuel and/or greases and oils

immediately.

・

Remove flammable materials in the site

before carrying out the grinding and welding

works of machine.

・

Do not use combustible materials to wash

parts such as light oil nor gasoline. Use

non-combustible oil as washing liquid.

・

Do not weld the pipes and tubes containing

combustible liquid and do not perform gas

cutting.

１

1.4.5

FIRE PREVENTION

FIRE CAUSED BY FUEL/OIL

Fuel, oil, antifreeze mixture, and window washer, etc. may catch a fire if a fire gets close to them.

Follow the instructions below without fail.

REFUELING

USE ANTI-EXPLOSION WORKING LIGHTS

Use only working lights with anti-explosion specifications when performing inspection and maintenance

procedures on fuel, oil, battery electrolyte, coolant and wind washer fluid to prevent a fire or

explosion. These flammable materials may catch a fire and then explode and result in severe injury.

［

1. SAFETY PRECAUTIONS

］

1-21

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands