Kobelco SK35SR-6 Operation Manual Download Page 245

Page: 245 / 296

To operate the breaker, press switch (1).

Release to stop operation.

Operate the breaker for 30 seconds, then

release the switch.

７

7.3

CONTROL OF PROPORTIONAL HAND CONTROL SWITCH

Read, understand and follow all safety precautions and procedures found in this manual before

attempting any operation of this machine.

For proper switching between the nibbler (crusher) and breaker, see "SWITCHING SELECTOR VALVE".

7.3.1

CONTROL LEVER SWITCH (BREAKER)

PRECAUTIONS FOR LEAVING THE OPERATOR'S SEAT

Do not leave the machine with the engine running.

Press switch (1) that is located on the right control lever to operate the "breaker".

The breaker can be operated by sliding nibbler (crusher) control switch (2) to the left. However, use

breaker control switch (button) (1) as much as possible.

［

7. NIBBLER (CRUSHER) AND BREAKER

］

7-9

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands