Kobelco SK35SR-6 Operation Manual Download Page 116

Page: 116 / 296

Affix a control pattern label (1) on the following

position.

Canopy specification: Guard divider to the

right of the operator's seat

Cab specification: Inside the cab door

CONTROL PATTERN LABEL

If you do not check the control lever pattern before operation, it is dangerous because it causes an

unexpected machine movement. Be sure to check the movement of each control lever before operation.

If you operate the machine while the control pattern labels do not match the actual machine

movement, it may cause severe accident resulting in severe injury.

Replace the control pattern label with the one matching the actual machine movement, or change the

lever pattern by the rotary multi-control valve to match the control pattern label.

The control pattern labels are magnetic.

They are needed when changing the control pattern. Keep them in a safe place.

Pattern labels

［

3. MACHINE OPERATION

］

3-22

Summary of Contents for SK35SR-6

































































































































































































































































Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands

Kobelco SK35SR-6, Operation Manual

Search results

Summary of Contents for SK35SR-6

Reviews:

Related manuals for SK35SR-6

Brands by name

Popular brands