Kobelco SK235SR-2 Operation Manual Download Page 92

Page: 92 / 308

The horn switch is a momentary push grey

button located on the operator's left control

lever.

This indicates the total time the engine has run.

Even if the excavator is not moving, the meter

continues to count as long as the engine is

running.

Swing parking brake is usually locked. The

swing parking brake is released in swing and

arm-in operation. When it cannot be unlocked

due to trouble, turn toggle switch to "Release

lock" (unlock), and the parking brake is

released. Then, move machine to safe area

immediately and contact our shop.

And return to toggle switch to "NORMAL"

position in normal condition.

10. Horn Switch

Always sound horn before starting engine to alert personnel that the machine is going to be operated.

11. Hour Meter

12. Swing Parking Brake Release Switch

［

2. MACHINE FAMILIARIZATION

］

2-30

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands